 | | Re: new RoboLab 2.5 compatible with old serial IR tower & RCX 1.0
|
|
(...) Richard (or others), I wish I knew where this info is coming from. Pitsco LEGO Dacta's web site has nothing I can find. I would like to know when Robolab 2.5 will be available and if there is an upgrade available to users of ver 2.0. And I (...) (25 years ago, 19-Sep-01, to lugnet.robotics.rcx.robolab)
|
| |
 | | Re: new RoboLab 2.5 compatible with old serial IR tower & RCX 1.0
|
|
Robolab 2.5 is rich with new features. These new features include support for the Lego camera and USB tower, support for Control Lab and the Scout brick, LASM support, support for the new RCX firmware for functions like events, auto-wire, better (...) (25 years ago, 19-Sep-01, to lugnet.robotics.rcx.robolab)
|
| |
 | | Re: 8 power levels, and only 8?
|
|
Hi, (...) Bummer! I was afraid I might get that answer... :o) (...) Sure, but maybe it would be worth it, since I imagine that many/some of us will make some silly, but basic routine that cycles between float/stop and some motor power, anyway... (...) (25 years ago, 19-Sep-01, to lugnet.robotics.rcx.java)
|
| |
 | | My HB wont get the bootstrap mode
|
|
I´m a new user on the HB, and whne I rey to get the bootstrap mode just I can't it suppose the 2 leds (red and green) should be on and rapidly turn off, but th green led stays on all the time... What is wrong?? Is the HB damage? (25 years ago, 19-Sep-01, to lugnet.robotics.handyboard)
|
| |
 | | Re: 8 power levels, and only 8?
|
|
(...) This is what the ROM routines support. (...) Yes, but then we'd need our own motor control routines in the lejos VM, and that would cost some precious memory. (...) Yes, the standard LEGO routines make it very hard to control speed. Basically (...) (25 years ago, 19-Sep-01, to lugnet.robotics.rcx.java)
|
| |
 | | 8 power levels, and only 8?
|
|
Hi there, Inspired by the answer by Juergen Stuber in the lejos/legos thread, I suddenly began to think about the fact that "we" only have eight power levels to choose among. Why is that? And can it be changed? When programming my bot for the W3D, I (...) (25 years ago, 19-Sep-01, to lugnet.robotics.rcx.java)
|
| |
 | | Re: Does lejOS has the same functions as legOS?
|
|
(...) No, for example LNP and speedometer are missing, motor control is standard with 8 power levels. In general it uses the standard ROM routines much more than legos. On the good side the rotation sensor problems it had until two months ago are (...) (25 years ago, 19-Sep-01, to lugnet.robotics.rcx.legos, lugnet.robotics.rcx.java)
|
| |
 | | RE: Solar panels, capacitor
|
|
I don't think it's practical to power the RCX with such small solar cells and capacitors. A device like the RCX does not like input voltage drops - the program will stop running, and the entire RCX will reset when power comes back up. Such drops are (...) (25 years ago, 18-Sep-01, to lugnet.robotics)
|
| |
 | | Re: Email Removal
|
|
Dean Husby writes: > rms2nsh@mandic.com.br > josh.winters@webstream.net Gone, both of them. > I'm surprised more of you don't complain. This is nuts. Gotta complain to me. I don't see 'em unless I post to the list. (25 years ago, 18-Sep-01, to lugnet.robotics)
|
| |
 | | Re: Using two RCX bricks in one robot
|
|
As long as there is some surface for the IR to bounce off, the bricks do not have to face each other. Sending messages is the technique that is used and is very effective. You can do this with any of the various programming languages. -- Bob Fay (...) (25 years ago, 18-Sep-01, to lugnet.robotics.rcx)
|