 | | Re: How to communication between RCXs without PC?
|
|
Thanks a lot, Michael. Is it possible to commucate between two RCXs and one uses legOS and another one uses NQC? I will read them, but could you give me a simplest sample here? (...) (25 years ago, 24-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: How to communication between RCXs without PC?
|
|
(...) Yes. Read the HOWTO section on LNP, which stands for legOS Networking Protocol. If you have any questions the HOWTO doesn't answer, feel free to ask here. (25 years ago, 24-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | How to communication between RCXs without PC?
|
|
I am thinking to convert NQC program to legOS, but I am not sure how to communicate between RCXs without PC (similar as SendMessage() and Message() in NQC), does anyone have experience? Zhengrong (...) (25 years ago, 24-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: bushing (bush) question
|
|
(...) Based on my experience, out of over 200 Type 1's that I own, only a few have ever split in half. Having recently acquired a used 8880 supercar (which uses Type 2's), I now have over 20 split Type 2's, and that number keeps increasing with use. (...) (25 years ago, 24-Aug-01, to lugnet.robotics, lugnet.technic)
|
| |
 | | Re: Power inlet to RCX 1.5?
|
|
(...) But what sort of Voltage and Amperage do you use with that connection? Coz, with me it won't work very well with a couple of adapters putting out 6 to 12 Volts (max. 1.25 A). Grtz., Remko (25 years ago, 24-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Power inlet to RCX 1.5?
|
|
(...) Check out this site, Jürgen: (URL) least it used to be there... Grtz., Remko (25 years ago, 23-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Proper power supply for a 1.0?
|
|
(...) First off have you connected the right two plates? First, I'd suggest using a 9 volt battery to find the right two plates. The RCX has built in reversed polarity so with a 9volt battery you won't damage anything. THEN ONLY USE 9 volts (...) (25 years ago, 23-Aug-01, to lugnet.robotics.rcx)
|
| |
 | | Re: bushing (bush) question
|
|
(...) They're pretty much the same. But I think Type 1 bushings often have a tighter fit than Type 2 bushings. It really depends on each specific part and its particular tolerances. I have some Type 1's that are extrememly tight fitting, and others (...) (25 years ago, 23-Aug-01, to lugnet.robotics, lugnet.technic)
|
| |
 | | Re: bushing (bush) question
|
|
(...) I don't have any hard evidence, but I've always found that the type 2's (later version) grip a little more consistantly. The type 1's in my collection are either *really* tight or just moderately tight. Type 2's seem to be consistantly (...) (25 years ago, 23-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Migrating from IR tower/spirit.ocx to USB
|
|
Take a look at the code in (URL) some examples. -a "Dave Hallowell" <lego-robotics@crynwr.com> wrote in message news:NEBBLJAEMKLDMPB...ems.com... (...) (25 years ago, 23-Aug-01, to lugnet.robotics)
|