To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *29469 (-10)
  Re: ir communication
 
(...) Chris (25 years ago, 14-Aug-01, to lugnet.robotics.rcx.legos)
 
  Re: Is Expansion Board Servo Voltage Suppose to Be 9v
 
Make sure you measure the voltage under load. Without a load the diodes won't look like they're dropping anything. Fred (...) (25 years ago, 15-Aug-01, to lugnet.robotics.handyboard)
 
  Re: Is Expansion Board Servo Voltage Suppose to Be 9v
 
Yes, Fred, the diodes are in place. I Assume that is where I should start to test for opens, shorts and, bad diodes. Thanks for the help. Andy "Fred G. Martin" <fredm@alum.mit.edu> wrote in message news:200108150241.WA...net.com... (...) (25 years ago, 15-Aug-01, to lugnet.robotics.handyboard)
 
  Re: WinVLL released
 
I received the Italian version Winvll.ini from Stefano Maffulli. Thank you, Stefano. I append it to the archive. And I wrote how to make VLL Probe page today. You can use the Winvll without USB Tower (RIS2.0). Please visit again my page. Now there (...) (25 years ago, 15-Aug-01, to lugnet.robotics, lugnet.robotics.edu, lugnet.robotics.microscout, lugnet.robotics.vll)
 
  updates to my site
 
Hi everyone, Just letting you know that I have recently updated my site. For those who haven't seen my site before, some of the highlights are: a Window walker, a photocopier, a Logo type Turtle, some gear boxes, etc. Building instructions for some (...) (25 years ago, 15-Aug-01, to lugnet.robotics)
 
  Re: Is Expansion Board Servo Voltage Suppose to Be 9v
 
Do you have the dropping 2n540x diodes in place? they should drop the 9.6v batt to the 5-6v servo voltage. Fred (...) (25 years ago, 15-Aug-01, to lugnet.robotics.handyboard)
 
  Is Expansion Board Servo Voltage Suppose to Be 9v
 
Hello again, I was surprised to find that my expansion board servo ports were putting 9 volts. Is this the way the board was designed or is this in error. Most servos I have come across work in the upper 4 to 6 volt range. The servo I have runs (...) (25 years ago, 15-Aug-01, to lugnet.robotics.handyboard)
 
  Help Needed With Serial Output Drivers Syntax
 
Does anyone have an example of how to use the 7i9600 serial driver with the Scott Edwards SSC II. I cannot seem to find any documentation. Thanks, Andy Loy andyl@citlink.net (25 years ago, 14-Aug-01, to lugnet.robotics.handyboard)
 
  Dos VLL Interpreter / Driver
 
Hi all; I have developed a DOS VLL Interpreter / Driver that does not use the Scout to talk to the MicroScout, rather it uses a simple LED driver circuit direct attached to the PC Parallel port. There are two versions; both DOS based. One is a (...) (25 years ago, 14-Aug-01, to lugnet.robotics.vll)
 
  Report from RoboCup 2001
 
RoboCup 2001 Seattle, WA August 2-10 2001 Same story, multiple URLs: (URL) site: (URL) (25 years ago, 14-Aug-01, to lugnet.mediawatch, lugnet.robotics.events)  

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR