 | | Project Questions
|
|
Three of us are undertaking a project using the Handyboard as the control system for a class at MIT. Our project, an autonomous blimp, has an unusual set of constraints, but we're hoping that your collective experience might be able to help us (...) (29 years ago, 9-Nov-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Burning hot motor driver chips.
|
|
Hello, RC car motors pull a lot of current, from 2A to 8A. The L293D chip goes up to 1A peak (for some miliseconds) before it shuts down. I suggest bypassing the L293D chips and using something like the LMD18200. (URL) Good luck, Marco A.A. de (...) (29 years ago, 10-Nov-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR devices
|
|
Hi Jeremy! I used the shaft encoder out of a track ball for my robotic project(same thing but a bit bigger). You do not need the IC out of the mouse just take the shaft encoder and use it with a IR led and detector pair. If you are going to use the (...) (29 years ago, 10-Nov-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Burning hot motor driver chips.
|
|
Anthony, As you've no doubt heard, RC motors take much more current than the Handyboard can supply. To control RC motors your only choice is to create a separate H-bridge to drive the motors. You can do this fairly inexpensively with power (...) (29 years ago, 10-Nov-97, to lugnet.robotics.handyboard)
|
| |
 | | L239
|
|
Does anyone know of a good source for the L293D or th TI SN754410? Future Electronics has them, but they want roughly $9.00 per chip. I am just looking for 4, but I don't want to be charged an arm and a leg to get them. Thanks ___...___ ___...___ (...) (29 years ago, 10-Nov-97, to lugnet.robotics.handyboard)
|
| |
 | | Expansion Board
|
|
It would be nice to see a set of raw, addressed digital OUTPUTS (as well as) analog OUTPUTS on the board. Maybe they are already on the handy board itself, however, they are not addressed on the data bus. The IC code libraries needed for this would (...) (29 years ago, 10-Nov-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: L239
|
|
Hi, I got L293E (the 20 pin DIP package) from Mouser at $2.53 each. 800-346-6873. John Bachman (...) (29 years ago, 10-Nov-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: L239
|
|
Jonathan: I have _dozens_ of L293's as well as L298's with motor controller circuit boards i would be pleased to sell to you if you like. L293's for $5.00 canadian. If you would like to see the motor controller, check my website at (URL) under the (...) (29 years ago, 10-Nov-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Burning hot motor driver chips.
|
|
What does "RC" stand for anyway? I don't think it's Radio Control...is it? ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the (...) (29 years ago, 10-Nov-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Burning hot motor driver chips.
|
|
(...) I believe that's correct: Radio Controlled devices, RC devices. Marco A.A. de Oliveira assfalk@eece.unm.edu ---...--- Autonom. Robotics (SMART) Project UNM/NASA ACE Center ---...--- (URL) ---...--- (...) (29 years ago, 11-Nov-97, to lugnet.robotics.handyboard)
|