 | | WINLNP QUESTIONS
|
|
Dear all, I have some troubles setting up WinLNP. I am new to RCX (2 months) and legOS (1 month) and have not much experience with VC6. I want to set up a line of communication between PC and RCX. I downloaded everything from (URL) and I managed to (...) (25 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: transfer data failed
|
|
(...) One other thing, did you erase the firmware from the RCX before trying to load legOS? regards Frank Caggiano "The best education for the best caggiano@crystal-objects.com is the best education for all." (URL) Robert M. Hutchins Logo Users (...) (25 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: transfer data failed
|
|
(...) Did you try slow? (25 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: transfer data failed
|
|
(...) Did you try using the slow mode option ("-s" for firmdl3) as was suggested? (25 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Scout Problems
|
|
(...) Ben, Are you using the version of RcxCC from my website ((URL) If you are then I'm sure I can help figure out what is going wrong. But I can't say anything for sure based on what you posted. What is it that is not working when you try to use (...) (25 years ago, 13-Aug-01, to lugnet.robotics)
|
| |
 | | Re: transfer data failed
|
|
Hi, thanks for the tips, but nothing helps. I tried 0.2.5, I tried the far and near mode, I changed the lighting conditions -> nothing helped. But I don't think that I fired up my Brick/Tower because the original Lego Software under Windows works, (...) (25 years ago, 13-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Scout Problems
|
|
I have got an RCX and a scout. I have used the special version of RCX CC that supports the scout. I doesn't work. Does anybody know what I am doing wrong - do I need any more software? I selected scout when it starts up. It works with my RCX. I was (...) (25 years ago, 13-Aug-01, to lugnet.robotics)
|
| |
 | | Re: New Palm IR Software to remote control your RCX
|
|
(...) It's very close to what is used in standard remote controls, so it's a natural choice and not that alien. They couldn't use the Irda protocol used in Notebooks or handhelds because it is too complicated for such a small computer as the RCX. (...) (25 years ago, 12-Aug-01, to lugnet.robotics.palm)
|
| |
 | | Re: WinVLL released
|
|
Hi, all: Do you enjoy my WinVLL ? Now I need your help. I try the WinVLL to the multilingual program. But I have Japanese Ed. Windows only. Would you help me to destribute non-English nor Japanese Ed. Winvll.ini file. Please visit for datailes: (...) (25 years ago, 12-Aug-01, to lugnet.robotics, lugnet.robotics.edu, lugnet.robotics.microscout, lugnet.robotics.vll)
|
| |
 | | RE: RIS 2.0 Software Question
|
|
(...) No, the whole thing runs at a fixed 800x600 setting. That's a step backwards from the 1.5 version, which could utilize up to 1024x768. Tilman (25 years ago, 12-Aug-01, to lugnet.robotics)
|
| |
 | | RIS 2.0 Software Question
|
|
Can anyone answer whether the RIS 2.0 software uses a full size 1024x768 display screen when available? I've only used a beta version of the RIS 2.0 software, and it only ran in 800x600 mode. The beta version also runs noticably slower than 1.5. I (...) (25 years ago, 12-Aug-01, to lugnet.robotics)
|
| |
 | | Re: New Palm IR Software to remote control your RCX
|
|
(...) I'm guessing that using the built in IR port is close to the signal needed but not quite there. It's a shame LEGO used such an alien signal for their towers. But I really do love having FULL NQC on my iPAQ! At our last show I was able to fully (...) (25 years ago, 12-Aug-01, to lugnet.robotics.palm)
|
| |
 | | Re: Remote Control with Palm
|
|
(...) Read (and post to) lugnet.robotics.palm for hand held devices. Dean -- Dean Husby LUGNET Member #320 TFM's LEGO Workshop - www.akasa.bc.ca/tfm The Vancouver LEGO Club - www.akasa.bc.ca/vlc/ (25 years ago, 12-Aug-01, to lugnet.robotics)
|
| |
 | | Re: New Palm IR Software to remote control your RCX
|
|
(...) Paul, Nice work - I installed it on my Visor Platinum, but it acts weird. The Forward/back arrows run motor A, the left/right motor B and the buttons to the right motor C. The motor 1/2/3 buttons do nothing and the stop button will not stop a (...) (25 years ago, 12-Aug-01, to lugnet.robotics.palm)
|
| |
 | | Remote Control with Palm
|
|
Hi, I would like to use my Palm m100 as a remote control for the RCX. The program I have found : LRemote doesn´t work. Any suggestions? Werner Dr. Werner Gieseke Fachberater für Informatik bei der Bezirkregierung Weser-Ems, Niedersachsen, (...) (25 years ago, 12-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Scout messages from to Rcx...
|
|
This is what each message (1-12) will command the scout to do: Message 1: Seek dark Message 2: Seek light Message 3: The Bug Dance Message 4: Forward A and B Message 5: Reverse A and B Message 6: Forward A, reverse B Message 7: Reverse A, forward B (...) (25 years ago, 12-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Lego kit inventories?
|
|
Also try BrickBay for individual parts: www.brickbay.com (...) (25 years ago, 12-Aug-01, to lugnet.robotics)
|
| |
 | | Fwd: FW: interesting info.
|
|
(...) ___...___ Get your FREE download of MSN Explorer at (URL) (25 years ago, 12-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Lego kit inventories?
|
|
(...) I started out buying kits for parts but found that to be expensive. Also, I got lots of parts I don't need. Now I get bulk parts from Pitsco LEGO Dacta, LEGO's educational arm, here: (URL) parts (such as differentials) I buy from Baylit, here: (...) (25 years ago, 11-Aug-01, to lugnet.robotics)
|
| |
 | | Re: RCX Talk to Scout?
|
|
No you don't need any special software (You can use RCX code, NQC etc.) If you look in the constructopedia for the Robotics Discovery Set you will see a list of commands on the back page. If you look it will tell you the function and a message (...) (25 years ago, 11-Aug-01, to lugnet.robotics)
|