 | | SetWatch() is remembered?
|
|
So does this mean that the RCX acts like a PC in that it does not forget the date/time when it is turned off or the batteries changed? Should I just write a one line program to set the time, and remove the time code from my actual NQC program? Thank (...) (25 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | maximum current of outputs
|
|
Hi hardware-specialists, does anyone know the maximum continuous current that a RCX motor output can drive? (I want to connect a light.) Thanks a lot. Bernd (25 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: transfer data failed
|
|
(...) Hi, i use 0.2.5 under Cygwin and sometimes i experience the same problem. I dont think its a problem with the legOS 0.2.4 distribution. The problem often occurs if its too dark or too bright in your room. It also happens if sender and receiver (...) (25 years ago, 7-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | RCX 2.0 Difference
|
|
I have got both an RCX1.0 and RCX2.0 unit. The RCX2.0 has a much less sensitive IR port. I would use the remote control to send messages and start and stop programs and to trigger motors. With the RCX1.0 the remote could be pointed at the unit and (...) (25 years ago, 7-Aug-01, to lugnet.robotics.rcx)
|
| |
 | | transfer data failed
|
|
Hi there, I use legOS 0.2.4 under Linux and tried (after a few weeks) to download the firmware and get always the follwing error: firmdl3/firmdl: transfer data failed Batteries are brand new, tower was set to short and long dist. nothing helped ... (...) (25 years ago, 6-Aug-01, to lugnet.robotics.rcx.legos)
|
| |
 | | RE: SetWatch() only accepts constants
|
|
Instead of sending ByteCodes from the PC and getting the RCX to interpret them, you can construct and send the SetWatch() OpCode plus the correct "constant" time and send it through Spirit.OCX (or directly, depending of the platform). (...) (25 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | SetWatch() only accepts constants
|
|
I just wrote a task and function that cause the RCX to receive data from the PC and then set the time on the RCX using SetWatch(). Unfortunately, I didn't realize that SetWatch() only accepts constants. NQC complained when integer variables were (...) (25 years ago, 7-Aug-01, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: How can I build sensor to measure eeg
|
|
(...) First, normal EEG is between 0.1 and 20 uV, with some exceptions uptil 100 uV. With a special (low noise, high CMRR) instrumentation opamp this would be no problem. Second, the highest frequency is about 120 Hz, so you need to sample at least (...) (25 years ago, 6-Aug-01, to lugnet.robotics)
|
| |
 | | Re: Rechargeable Batteries
|
|
I have been interested in what people have to say about using 1.2v cells instead of 1.5v. I don't think the RCX minds, but what is a problem to my mind is that after the RCX motor drivers drop about a volt from the already low 7.2v, you end up (...) (25 years ago, 6-Aug-01, to lugnet.robotics)
|
| |
 | | Robolab software
|
|
Any one have a copy of the robolab software for Macintosh available. I have the mindstorm kit but cannot run it on my Mac. I know I can spend $60 bucks at Pitsco and buy a copy, but somehow it doesn't seem fair that they have the Mac version and (...) (25 years ago, 6-Aug-01, to lugnet.robotics)
|