 | | Re: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
Oh, geez, this could be bad. Could changing the firmware to reduce comm activity fix this? It seems to be a problem of usage, not specific firmware properties (i.e. constant data uplaoding.) Andy (...) -- See my Visual Interface for leJOS at (URL) (25 years ago, 27-May-01, to lugnet.robotics)
|
| |
 | | Re: lnp rcx hostaddress [and a summer legOS release?]
|
|
Vittorio- I've frequently wondered the same, but since I've never had reason to use LNP I've never fixed it. If you'd like to submit a patch I'll gladly apply it to the source tree. In other news- I'm back, more or less. While this week will be (...) (25 years ago, 27-May-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
The following information is my own opinion and not endorsed or verified in any way by LEGO. That being said, I think that now is the time to relate some experiences I've had over the past couple of months with my RCX and IR tower - and it boils (...) (25 years ago, 27-May-01, to lugnet.robotics)
|
| |
 | | lnp rcx hostaddress
|
|
I have an important question: WHY the rcx lnp address (and mask) is hardcoded in the library? I inspected the source code for both the pc part and the rcx part. The pc library is well formed and the init function allows you to set up the address and (...) (25 years ago, 27-May-01, to lugnet.robotics.rcx.legos)
|
| |
 | | new MOC
|
|
will be up soon at the mindstorms site. page will be available soon at (URL) now use the pictures (URL) just browse (URL) least I hope that will work soon, prohosting is kinda buggy... well off to the pavement again. mike "found a use for the R@D (...) (25 years ago, 27-May-01, to lugnet.robotics)
|
| |
 | | Re: problem with floating point numbers (legOS 0.2.5)
|
|
(...) You are the second person to report something like this, so there must be something wrong somewhere. I will take a closer look at this when I get a chance. I am busy until Tuesday though. I know I will forget, so keep e-mailing me until I fix (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: IR Tower Use
|
|
(...) This isn't true at all. The tower converts an RS-232 serial transmission directly into IR and vice-versa. It is a pretty standard protocol. -Kekoa (25 years ago, 26-May-01, to lugnet.robotics.rcx, lugnet.robotics, lugnet.off-topic.geek)
|
| |
 | | Re: IR Tower Use
|
|
(...) You can't really do what you are trying to do. The tower is designed to operate in request-reply mode. It sends a request, waits a few seconds, receives a reply during that time, then turns off. The idle state of the tower is off, and (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx, lugnet.robotics, lugnet.off-topic.geek)
|
| |
 | | Re: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
(...) Maybe this is shedding some light on why LEGO removed the Power Port in the 1.5's. To remove a known problem without dealing with it.?.?.? Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 26-May-01, to lugnet.robotics.rcx)
|
| |
 | | RE: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
Even more interesting.... I've also just replaced the IRED I replaced a few hours ago in my RCX :-( This time, I'm putting a limiting resistor between the IREDs in the RCX to keep the current within limits. The following is pure conjecture on my (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx)
|