 | | Re: problem with floating point numbers (legOS 0.2.5)
|
|
(...) You are the second person to report something like this, so there must be something wrong somewhere. I will take a closer look at this when I get a chance. I am busy until Tuesday though. I know I will forget, so keep e-mailing me until I fix (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: IR Tower Use
|
|
(...) This isn't true at all. The tower converts an RS-232 serial transmission directly into IR and vice-versa. It is a pretty standard protocol. -Kekoa (25 years ago, 26-May-01, to lugnet.robotics.rcx, lugnet.robotics, lugnet.off-topic.geek)
|
| |
 | | Re: IR Tower Use
|
|
(...) You can't really do what you are trying to do. The tower is designed to operate in request-reply mode. It sends a request, waits a few seconds, receives a reply during that time, then turns off. The idle state of the tower is off, and (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx, lugnet.robotics, lugnet.off-topic.geek)
|
| |
 | | Re: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
(...) Maybe this is shedding some light on why LEGO removed the Power Port in the 1.5's. To remove a known problem without dealing with it.?.?.? Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 26-May-01, to lugnet.robotics.rcx)
|
| |
 | | RE: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
Even more interesting.... I've also just replaced the IRED I replaced a few hours ago in my RCX :-( This time, I'm putting a limiting resistor between the IREDs in the RCX to keep the current within limits. The following is pure conjecture on my (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx)
|
| |
 | | RE: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
(...) Actually, there's a regulator on the Tower that takes the voltage for the digital side to +5 and keeps it there. The capacitor is only rated for 10V. The higher voltage will allow higher current through the IREDs as they are connected right to (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx)
|
| |
 | | Re: Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
(...) I'm pretty sure I know your problem to your number 2... The IR Tower has no protection against higher power. Running an unregulated power source into the IR tower is not a good idea! Use a 9v regulator package (The little 3 prong packages with (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx)
|
| |
 | | Custom Firmware, IR Problems, and Dead RCXs (long)
|
|
The following information is my own opinion and not endorsed or verified in any way by LEGO. That being said, I think that now is the time to relate some experiences I've had over the past couple of months with my RCX and IR tower - and it boils (...) (25 years ago, 26-May-01, to lugnet.robotics.rcx, lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx.legos)
|
| |
 | | Asking about Firmware (need help)
|
|
Dear All I`m a newbies in programming LEGO Mindstorms RIS. I have explored CD that embedded in my RIS KIT. Now i want to try make a user interface for LEGO Mindstorms RIS in my own language. I used microsoft visual c++ to build my software From the (...) (25 years ago, 26-May-01, to lugnet.robotics)
|
| |
 | | Re: i neeeeeed help! can't logon to the lego site
|
|
(...) After moving to a new computer, Win98 and MS Internet Explorer 5.5 I found I could get into every site ...except... www.hp.com and www.kodak.com. On my old computer and Win95 no problem but consistent 'timeouts' on those two sites. I still (...) (25 years ago, 26-May-01, to lugnet.robotics)
|