To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *27619 (-10)
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
As an alternative method to tubing, you can use an IR filter (black inversible film) as described on my page : (URL) doesn't work with Lego visible lamp though... Philo (URL) (26 years ago, 29-Mar-01, to lugnet.robotics)
 
  Re: Lego accessories for the photographer
 
(...) Sort of... I borrowed the older Coolpix 900 I have at my office ;o) It is quite good for the kind of resolution needed for the web ! Philo (...) (26 years ago, 29-Mar-01, to lugnet.robotics)
 
  Re: Robot navigation - barcode stations?
 
I think it's an excellent idea... I saw the barcode system being explained some years ago and I still think it can be the most accurate. One thing that's different in the system I saw was that there were no LED's used (not needed...) and it would (...) (26 years ago, 29-Mar-01, to lugnet.robotics.rcx)
 
  Ser. Col. Only!! I'll cover shipping!!
 
(26 years ago, 29-Mar-01, to lugnet.robotics.rcx.legos)
 
  Serious Collectors Only!
 
I'm selling my entire collection for $4,500. There are over 300 sets MISB, and over 200 sets opened but still in mint condition. Over 90% of the opened sets were put together once; and then sealed in zip-lock bags. The boxes of the MISB sets are in (...) (26 years ago, 29-Mar-01, to lugnet.robotics.rcx.legos)
 
  Unsubscribe
 
Sorry, I knew I shouldn't post this but I can not unsubscribe to this newsgroup. I have tried to stop this by going through the option and it doens't recognize this subscription. Please take t-f-l-y@home.com out of you system. Thanks (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
(...) You can find light sensor schematics on Michael Gasperi's page: (URL) Using the RCX IR emitter as the illumination source. Don't know (...) Someone has already tried this. You can check Simen Svale Skogsrud's page for an example, with NQC (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
 
  Re: Assembly in my C-program
 
(...) If you want to drive directly the motors you should first disable motor handling in legOS (remove CONF_DMOTOR definition in config.h). Then you can create a high priority task that switches motors on and off writing in the motor output port. (...) (26 years ago, 28-Mar-01, to lugnet.robotics.rcx.legos)
 
  Re: Assembly in my C-program
 
(...) pulses (...) at (...) would (...) Hmmmm. This should be possible, but it's a bit more tricky with stepper motors - you have to allow for the speed-up and slow-down. Thus just calling motor_speed(50) would have to initiate a task that starts (...) (26 years ago, 28-Mar-01, to lugnet.robotics.rcx.legos)
 
  Re: Shutting off illumination LED on Light Sensor for LIDAR
 
Ralph Hempel had an example of the heat-shrink tubing solution here: (URL) also tried used some black vinyl from a binder? -Tim (...) (26 years ago, 28-Mar-01, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR