To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *26309 (-10)
  Any idea how to get to run "Vision Command" under W2K?
 
Hello, everybody! Does someone have an idea, how to get the Mindstorm Vision Command to run under Win2000? Can you fool the software somehow (e.g. with VirtualPC)? Or are there W2K-driver-betas somewhere? On "NT Compatible" they say Lego Mindstorms (...) (26 years ago, 24-Jan-01, to lugnet.robotics.vc)
 
  Visual NQC 2001 Beta 2
 
To all testers, Runtime error 380 stands for invalid property. This can happen when you try to compile a program in the editor. I had the error ones during development but it didn't come up anymore. Next week I'm starting bugfixing again and see if (...) (26 years ago, 26-Jan-01, to lugnet.robotics.rcx.nqc)
 
  fiber optics conduit to light sensors
 
You can make a sturdy fiber optic cable conduit from Lego tubes and connectors. It can completely enclose at least two Lego fiber optic cables joined end-to-end from a light source to a light sensor. The conduit can shield a light sensor from (...) (26 years ago, 26-Jan-01, to lugnet.robotics.scout, lugnet.robotics.microscout, lugnet.robotics.vll)
 
  Re: How many motors can accept a RCX ?
 
The outputs on the RCX can sink about 500mA of current, and each motor draws up to 200mA when stalled. You can put two on the output and stall them before the thermal shutoff kicks in. I was under the impression (never tried it, mind you) that the (...) (26 years ago, 26-Jan-01, to lugnet.robotics)
 
  dodgy motor
 
The motor I got with my 8479 is very stiff - it can only be turned by hand with difficulty. It drives with power but more slowly than any others I have. It's not essential that I replace it as I have enough (from znaps etc). What should I do - put (...) (26 years ago, 26-Jan-01, to lugnet.robotics.codepilot)
 
  Re: Rotational Sensor & Gearing Down
 
(...) I find it really frustrating that this has to be "discovered" over and over. I believe my fix for LegOS (a year ago?) fixes this problem. The sensor itself is very good. It only ever returns the discrete voltages (which vary by cable length (...) (26 years ago, 26-Jan-01, to lugnet.robotics)
 
  Re: Rotational Sensor & Gearing Down
 
"Steve Baker" <lego-robotics@crynwr.com> wrote in message news:3A6EFF8A.416F3D...ail.net... (...) Nice post, but you only ran the sensors counting up for x number of seconds. Try *reversing*. Then watch what happens... (IE, bring a sensor back home. (...) (26 years ago, 26-Jan-01, to lugnet.robotics)
 
  How many motors can accept a RCX ?
 
Hi, everybody <DISCLAIMER> Excuse me first for my newbieness here on Lugnet. and also for my frenchieness, but it's not my fault ! </DISCLAIMER> I have a question I'd like to submit: Because of extreme needs of power/ acceleration (it was about (...) (26 years ago, 26-Jan-01, to lugnet.robotics.rcx)
 
  Re: Rotational Sensor & Gearing Down
 
Thanks to all for the good information that has been related here. Most of my applications were low rpm which seems to be a definite fault area. I like to use them for absolute programming of positions. I now see the problem in using them in these (...) (26 years ago, 25-Jan-01, to lugnet.robotics)
 
  Re: Rotational Sensor & Gearing Down
 
(...) Just don't go past it's Max or Min areas or you'll have a problem. This is probably a good place for the white slip gear... Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (26 years ago, 25-Jan-01, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR