 | | Re: IR Tower problems
|
|
(...) I think it could probably work with the printr port. But what I would do is get a serial to printer port adapter or buy another wire which ever is cheapest. I have a wire that runs out the serial port with a 25 pin(i think) connection then an (...) (26 years ago, 21-Jan-01, to lugnet.robotics)
|
| |
 | | Re: Interfacing Sharp's GP2D02 Distance Sensor to the RCX
|
|
Hi, I asked this problem a few weeks (or months??? ... I don't know a what time ...) but nobody could help. I got the same following answer ".... the sensor takes 35 mA and this is to much for the RCX ..." but I couldn't understand this at this (...) (26 years ago, 21-Jan-01, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
 | | Re: programming interface i think
|
|
Don't shoot me if i'm wrong, but this site seems to be mainly about heat and energy. There is a link about using the RCX with Borland C++. When you download the file, you get the information on how to do this (in english) frank "not much left to (...) (26 years ago, 21-Jan-01, to lugnet.robotics)
|
| |
 | | RE: Anyone made animatronics with the RCX yet?
|
|
(...) I know this only works with pbForth, and it's not ALL Technic, but you can drive standard servos with the RCX. Here's how: (URL) You can even drive pneumatic switches with the servos... Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH (...) (26 years ago, 21-Jan-01, to lugnet.robotics.rcx)
|
| |
 | | Re: IR Tower problems
|
|
(...) Hi Greg, I'm not sure if the RCX IR Tower is the same than the Scout Tower, but I guess it's so. You can't use the printer port (LPT) for the tower. You have to use a serial port (COM1, COM2, ..). If you're not sure if you've got the right (...) (26 years ago, 21-Jan-01, to lugnet.robotics)
|
| |
 | | Re: IR Tower problems
|
|
(...) Eep!!! Not PRINTER port but the SERIAL port. You'll damage your Port and maybe the IR tower as well! Try it in the SERIAL port and it will work much better. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (26 years ago, 21-Jan-01, to lugnet.robotics)
|
| |
 | | Re: Anyone made animatronics with the RCX yet?
|
|
(...) I tried to have my Raptor puppet set up with Pneumatics but I gave up because I couldn't find a decent way of triggering it. The ways I had it were way to slow and painful. Has anyone come up with a great way of using pneumatics with (...) (26 years ago, 21-Jan-01, to lugnet.robotics.rcx)
|
| |
 | | IR Tower problems
|
|
I recently purchased an IR tower to use with my Scout. It did not come with a cable, but the tower was only 6$(www.eblok.com), so I found a cable that could plug into the back of it. The other end of the cable fit into the printer plug on the back (...) (26 years ago, 21-Jan-01, to lugnet.robotics)
|
| |
 | | Re: LegOS 0.2.5 and LNP
|
|
(...) Ok. Checking and testing never hurts :-). (...) It's not for performance, but for correctness. The old code was like this: if(lnp_addressing_ha...ler[port]) { ... lnp_addressing_handl...th-2,src); You first test lnp_integrity_handler and then, (...) (26 years ago, 21-Jan-01, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: LegOS 0.2.5 and LNP
|
|
(...) you may see (...) give access (...) the handlers (...) My only (...) depend on. (...) introduce a (...) this point to (...) I think that we can use safely (CONF_TM || defined CONF_HOST) condition. I'm checking the whole patch and I think that (...) (26 years ago, 21-Jan-01, to lugnet.robotics.rcx.legos)
|