 | | Lcd
|
|
Can anyone tell me the relevent information for choosing an LCD?I want to change mine for a backlit one and would like to make as few modifications as possible so I think I need to know pin outs(is that all?) and I may have to supply an extra +5v (...) (29 years ago, 18-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | H-bridge stuff on-line
|
|
I've created a MOSFET version of my H-bridge that is pretty general purpose and with the addition of a small mezzanine board becomes an electronic speed control. There is a web page that describes the PIC servo code at: : (URL) above paper describes (...) (29 years ago, 17-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | IR Transmitter
|
|
Hi all, I was wondering if anyone could recommend an IR transmitter for use with the Handy Board's IR output (J7). If possible indicate manufacturer/part no. or supplier/catalog no. if possible. I was also wondering if anyone could tell me how (or (...) (29 years ago, 17-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: positioning of robot
|
|
First, my appologies that this posting is off the mailing list's intended topic (the HandyBoard) but as it seems to be drawing a lot of interest I am hoping that continuing it is ok with everyone?) (...) Ok- first a disclaimer - I am not an (...) (29 years ago, 16-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: positioning of robot
|
|
I had some questions regarding John Whitten's recent posting about different drive types. (...) How is the math to figure out the narrowest space a vehicle can turn around in done? (What formula -- or formulas -- are used? Don't just give names, (...) (29 years ago, 16-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | thanks
|
|
As I just hooked up my Vector 2x compass to my handyboard and it worked the first time, just like my sonar did, I just want to say, thank you all very much for all of the help everyone gives. Thanks -Jim (URL) (29 years ago, 15-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: positioning of robot
|
|
I missed the first posting, I liked the summary posted by John Whitten. Youcan take his posting one layer "up" to get at the abstractions if you want. These are: 1. Points of contact with the surface - More increases stability. 2. Drive Train (...) (29 years ago, 15-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: positioning of robot
|
|
I think the Tyco ZIG ZAG makes a great platform. It is a treaded vehicle with a center motor/wheel set that moves it sideways. I haven't complete a robot with it yet but you may want to look into it. jm (...) (29 years ago, 15-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: positioning of robot
|
|
(...) Howdy- (...) No problem- as long as you get the relevant points across- that's what counts :) (...) Ok- that's a very good basic question. Here are the pluses and minuses for each type of drive system: 2 WHEELS: The two wheel drive system on (...) (29 years ago, 15-Aug-97, to lugnet.robotics.handyboard)
|
| |
 | | HB sampling rates
|
|
Hello all, Does anyone know the maximum sampling rate possible on the HB for an analog input being polled in Interactive C 3.1? Thanks, Colby (29 years ago, 14-Aug-97, to lugnet.robotics.handyboard)
|