To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *2551 (+10)
  Re: ? mobile base for handyboard
 
Depends on what you want to accomplish. The LegoBug can use otpical sensors to follow a black tape and the smaller 'micro-motors' are better (less play) than the standard 9v motors. check out (URL) for instructions, ordering info and a price list. (...) (29 years ago, 4-Aug-97, to lugnet.robotics.handyboard)
 
  IR output on HB
 
Hi, I'm trying to get the ir output on the handy board to power more than 4 LEDs (need to power 6), anything beyond that the ir signals become drastically weak. I have these LEDs wired serially. I'm not too familiar with electronics, so is it (...) (29 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
 
  3v motors
 
I have a cute little tracked robot base i want to run from a handyboard, but the problem is that it has 3V motors. The handyboard is set up to power 9v, right? The way i see it, i can either just put a resistor in series with the motor to drop the (...) (29 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
 
  3V motors
 
Mike, I had a similar problem and the solution is not to put a resistor in series with the motors. With the varying amount of current a motor draws, the voltage drop across the resistor will vary as well and the motors will not see a consistent 3V. (...) (29 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
 
  CdS cells
 
hi everyone, I am looking to purchase a batch of CdS photo cells but I think that I need more information before I order. The catalogs (Digi-Key, Mouser, etc.) list several different photocells (different resistances, power dissipation, etc.) and I (...) (29 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
 
  Re: CdS cells
 
[David.J.Dostal@lawrence.edu] spake unto the ether: (...) I just ordered some from Mouser, the smaller of the two physical sizes they have, 3K to 100K I believe are the light/dark resistances. These give analog(PORT) values of about 10 in ordinary (...) (29 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
 
  Re: IR output on HB
 
Run them in parallel, use a transistor. Like so: +5v | +---+---+---+---+---+ | | | | | | \ \ \ \ \ \ / R / R / R / R / R / R \ 1 \ 2 \ 3 \ 4 \ 5 \ 6 / / / / / / -- -- -- -- -- -- \/ \/ \/ \/ \/ \/ -- -- -- -- -- -- HB + | | | | | | \ | | | | | | / (...) (29 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
 
  Re: IR output on HB
 
No, don't use a transistor! The HB's IR out already has one. But the parallel-with-a-sepa...r-for-each method is correct. -Fred In your message you said: (...) (29 years ago, 5-Aug-97, to lugnet.robotics.handyboard)
 
  MAgentic card readers again...
 
Anyone can help me about the way to connect a magnetc card reader to the handy? I use the idea from david negro , that use the SPI port, but i don't can make work the code... Can anyone tell me uf exists other source of that info ont the web?? (...) (29 years ago, 6-Aug-97, to lugnet.robotics.handyboard)
 
  Motors
 
Hi. I am running two 3.3V motors with the handy board. Sometimes The motors would just stop running. The leds that indicates the motors are running are still lit. Also the two chips next the motor output gets very hot. The number on the chip is (...) (29 years ago, 6-Aug-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR