To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *24889 (-10)
  Re: Another DIY sensor
 
(...) All optical mice use the HDNS-2000 (short: HD 2000) chip from Agilent Technologies. There are two output modes: the rs232 output and the quadrature output mode. The quadrature output gives the Delta X and Delta Y values (how much the x,y (...) (26 years ago, 17-Nov-00, to lugnet.robotics)
 
  Re: Batteries...
 
Yes, it's possible. You get less voltage with NiCads, so the motors don't turn as fast as they do with brand-new alkalines. Plus they don't last as long. However, they're so much cheaper to run! I used to use NiCads during development and general (...) (26 years ago, 15-Nov-00, to lugnet.robotics.rcx)
 
  Re: Sets with worm gear box?
 
I just tried to send this reply directly to pavogel@pacbell.net and my message is returned as undeliverable. Is this some kind of "special" email address? So here is my answer, to the more general audience, please forgive; The two odd pieces, in (...) (26 years ago, 17-Nov-00, to lugnet.robotics)
 
  Re: Another DIY sensor
 
(...) Those cameras have a small, low-resolution CCD in them, and they take snapshots of the mousing surface and compare them to detect the quantity of motion. If you were going to use one of those mice your best bet would be to put together a (...) (26 years ago, 16-Nov-00, to lugnet.robotics)
 
  Re: Another DIY sensor
 
(...) Did you consider buying a $5 computer mouse and gutting it? That will give you not one but TWO slotted disks and TWO dual optical detectors. It's hard to imagine another solution for $2.50 per sensor! IIRC, most cheap mice are ~200 clicks per (...) (26 years ago, 16-Nov-00, to lugnet.robotics)
 
  Re: Another DIY sensor
 
The optical mice are still $50. I bought one and ended up taking it back, didn't work so well. But it definitely looked cool. Would probably make a good sensor though I don't know what kind of values it sends out... (...) (26 years ago, 16-Nov-00, to lugnet.robotics)
 
  Re: Another DIY sensor
 
(...) How about (URL) you filter out the marketing-speak it would appear that the optical sensor is a combination digital camera and signal processor. Dunno what the chances are of getting any sort of intelligle output other than +/- x and y is. (...) (26 years ago, 16-Nov-00, to lugnet.robotics)
 
  A technic elevator
 
I have updated my Lego page with my new own creation : a Lego elevator. (URL) Klein A Mindstorms fan. (26 years ago, 17-Nov-00, to lugnet.robotics, lugnet.technic)
 
  Re: Float?
 
Yes. Install the "extras" from the "project" menu. You will then get a yellow stop sign, which floats the motors instead of brakeing them. Wire in the ports to be floated. -Peter Coach, FLL Team #1096: The Unibots "J G Gregory" <jgg@ultranet.com> (...) (26 years ago, 17-Nov-00, to lugnet.robotics.rcx.robolab)
 
  Re: I/O port of H8/3000
 
(...) Are they all used? No. See the H8/300 manual and the bottom section of: (URL) visit the Microcontroller Interface section of my horribly-incomplete Low-level RCX Reference, at: (URL) unused pins are better documented in the low-level (...) (26 years ago, 17-Nov-00, to lugnet.robotics.rcx)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR