 | | Robotized panoramic head
|
|
Hi everybody! I recently uploaded on my site PanoBot2, a RCX-controlled panoramic photography head, which can be build with RIS 1.5. See it, along with full building instructions, LeoCad files and sample panorama photographs at (URL) (26 years ago, 16-Oct-00, to lugnet.announce, lugnet.robotics)
|
| |
 | | Re: Meaning of lettering on white gearwheel.
|
|
Ncm is the metric measure for torque, imperial is ft/lb's hence 5Ncm is the the amount of torque required before the gear will 'slip', 2.5Ncm before it will engage again. the difference is the hysterisis. one would assume that Lego has a range of (...) (26 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Meaning of lettering on white gearwheel.
|
|
(...) teeth (...) rotation (...) As far as I can tell, the minimum "breakaway" torque would be 2.5 Ncm (which would be Newtons*cm, or 2.5 Newtons weight, hung 1 cm out, or 1 Newton hung 2.5 cm out (about .22 of a lb, at 1" radius for those of you (...) (26 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Meaning of lettering on white gearwheel.
|
|
(...) is (...) teeth (...) is (...) rotation (...) further? I'm not a real physicist so I'm taking the risk to add confusion instead of knowledge :-) I heard that the 2.5 and 5.0 numbers refer to the threesholds the gear starts to slip in the two (...) (26 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
 | | Where can i get a kit to build?
|
|
Hello. i want to build a handyboard but live in Scotland, U.K. Can anyone point me towards a location that i will let me buy a handy board in kit form. Cheers. (26 years ago, 11-Oct-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Meaning of lettering on white gearwheel.
|
|
(...) I do know they seem to wear out REALLY fast and no longer work as new ones... Mine can now barely turn it's self with out slipping. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (26 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
 | | (canceled)
|
|
|
| |
 | | Re: Scout SDK
|
|
Hi Mauro The link is (URL) take a look at (URL) just search hte newsgroup for vll. There's a lot of stuff out there... :o) <>s Ricardo (...) (26 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
 | | VC use with Macintosh?
|
|
Hello, i don't yet have the Vision Command because i have a Mac. However, i note that the Vision Command makes use of a USB interface. Has anyone tried using this camera with the MacOS? Who makes the camera? I was thinking that perhaps there might (...) (26 years ago, 16-Oct-00, to lugnet.robotics.vc)
|
| |
 | | Re: Meaning of lettering on white gearwheel.
|
|
(...) I think Ncm is Newtons per centimeter, but I can't remember how a Newton is defined. So, if you're spinning the drive shaft, and the counter force on the gear teeth is less than 2.5 Ncm, you're fine. If the counter force on the gear teeth is (...) (26 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Scout SDK
|
|
(...) I would try looking for it at www.legomindstorms.com --Todd (...) (26 years ago, 16-Oct-00, to lugnet.robotics, lugnet.robotics.scout, lugnet.robotics.vll)
|
| |
 | | Pneumatic actuators
|
|
Hi, Can anyone tell me in witch set I can find pneumatic actuators and pumps. Thanks from Argentina Luis Alberto González luis_gonzalez@radar.com.ar ARGENTINA (26 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
 | | Meaning of lettering on white gearwheel.
|
|
On the white 'slipping clutch' 24t gearwheel part is written: 2.5 5.0 Ncm 2.5 5.0 Ncm What is the significance of this? (26 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
 | | Scout SDK
|
|
Hi, I'm looking for the Scout SDK at www.mindstorms.com but I can't find it. Is it still available? I'd like more information about the VLL protocol... Thanks, Mauro Vianna (26 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Motion/Tilt Sensor from Analog Devices and the RCX
|
|
BTW, the Duplo MyBot control unit must have a similar sensor built in. It detects acceleration or tilt in four different directions. It's a closed system however, powered by 2 AA batteries. The set is $50 - not a cheap source for ripping apart for (...) (26 years ago, 16-Oct-00, to lugnet.robotics)
|
| |
 | | VC: Fun, fun, fun!
|
|
The VC is a great toy! When using the camera together with the RCX, you really get a lot of new ways to control your robots! Especially the ability to react to motion is very good, while recognition of colors is a bit more tricky, and quite (...) (26 years ago, 15-Oct-00, to lugnet.robotics.vc)
|
| |
 | | Re: Rotation sensor
|
|
(...) <set:9756> alone or <set:3801> as part of the Ultimate Accessory Set. BEN GATRELLE (26 years ago, 15-Oct-00, to lugnet.robotics)
|
| |
 | | Rotation sensor
|
|
Can any one tell me the S@H order number for the rotation sensor? Thank you (26 years ago, 15-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Memory Usage
|
|
(...) Ok, thanks. I'll try everything else first, then try this if I get desperate. The main thing I hit a wall with was when I switched to floating-point, which increased my .lx filesize by about 2k, so if I go back to fixed-point, turn sound off (...) (26 years ago, 15-Oct-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Motion/Tilt Sensor from Analog Devices and the RCX
|
|
Hi, I just order two free samples of Analog Devices ADXL202E at (URL) Anyone know if this can be hooked up to the RCX? Ram PS: Try to get a free subscription to "Sensors". It is a really cool magazine... (26 years ago, 15-Oct-00, to lugnet.robotics.rcx, lugnet.robotics)
|