 | | Linux and v1.21 handyboard (fwd)
|
|
Hi, I've successfully located and compiled the IC files for the Handy Board. I can load and run programs on the board, BUT the digital input(s) are not being "seen". E.g. a simple program like: void test3(){ while (1){ if (digital(10)) printf("10 is (...) (26 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: The datalog
|
|
(...) numbers. It can only log timers, sensors, variables, and the system watch. When a value is logged, its source is also logged. For example, AddToDatalog(Timer(1)) adds the current value of Timer 1 to the log and also stores that this entry came (...) (26 years ago, 5-Oct-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | communication via serial port
|
|
Hi, This isn't an off topic question... Has anyone tried programming the serial port (on Linux) to communicate with the Handyboard? I am working on an RF link between the Handyboard and a PC via serial communication, but I don't know much about (...) (26 years ago, 5-Oct-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: external power
|
|
I am by no means an expert on the subject but this is how I did it. First I cut the heavy motor power trace as shown in the FAQ. Next I soldered a four pin female header on top of the expansion board where the expansion board picks up power for the (...) (26 years ago, 4-Oct-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: A neat idea for touch sensors
|
|
(...) Those resistors in the Cybermaster touch sensors are in parallel to the sensor. You can read its value when the sensor is not pressed. Cybermaster uses it to figure out which sensor is connected to what port before starting the actual program. (...) (26 years ago, 4-Oct-00, to lugnet.robotics)
|
| |
 | | Re: Book thought...
|
|
I'd like to go on and on about it, but I haven't heard the official word yet as to what I should/could say and not say. The publisher is Addison Wesley Longman, and I'm really not positive when it will be out (don't know how long it takes for (...) (26 years ago, 4-Oct-00, to lugnet.robotics, lugnet.robotics.edu, lugnet.edu)
|
| |
 | | Re: Sharp GP2D05 Infrared Ranger and the RCX
|
|
Hey, my GP2D12 just showed up. I ordered it from Acroname. It comes with a nice little booklet with details on how to rig it, and it even has some Handyboard code and interface info. I have test equipment in my lab too. I'll plug it into a power (...) (26 years ago, 4-Oct-00, to lugnet.robotics.rcx)
|
| |
 | | Re: Book thought...
|
|
Being lazy, I was hoping that would be the case :-) When will it be out? Who's publishing? Thanks! -Peter "Ben Erwin" <ben@alum.mit.edu> wrote in message news:G1xADI.33s@lugnet.com... (...) late (...) books, (...) concepts (...) RCX (...) in (...) (26 years ago, 4-Oct-00, to lugnet.robotics, lugnet.robotics.edu, lugnet.edu)
|
| |
 | | Visual J++?
|
|
Has anyone used the OCX with Visual J++? Have any examples? -ben (26 years ago, 4-Oct-00, to lugnet.robotics.rcx.java, lugnet.robotics.rcx)
|
| |
 | | Re: Book thought...
|
|
I have just finished this EXACT book, so I'm sorry, but its a little too late to collaborate. :) And although the audience is broader than the other books, i certainly have not left adults out, as there are plenty of advanced concepts in the book as (...) (26 years ago, 4-Oct-00, to lugnet.robotics, lugnet.robotics.edu, lugnet.edu)
|