 | | Re: External supply for RCX
|
|
(...) No one has answered your Question fully so here goes. The RCX with the power Adapter port is the 'old' one. It's power port can take the following: AC or DC (It doesn't matter what direction) AC is a little easier on the RCX as it uses both (...) (26 years ago, 2-Sep-00, to lugnet.robotics)
|
| |
 | | Re: Info request
|
|
Take a look at the original reverse engineering of the RCX at (URL) best site for the internals of the RCX with pictures.... Ram PS: You could probably just use wireless serial radio modems for this! It works as follows: PC--->serial (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Vision Command in Nederland
|
|
Is Vision Command te koop in Nederland? Zo ja, waar? Does anybody know whether Vision Command is sold in the Netherlands? If yes, where? Harrie de Leeuw Eindhoven The Netherlands (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Info request
|
|
Ok, enough's enough! I'm going to take a crack at the IR - RF link thing for the RCX. I'm not promising it's going to be pretty (or cheap) though! But I'll try. First of all, a question - Does anybody know if the schematics for the RCX and more (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: External supply for RCX
|
|
(...) Yes - but alkaline batteries drop gradually in voltage throughout their lives - by the time they run out, their volts are below 1.2. NiCd's on the other hand stay at 1.2 volts and dry up much more suddenly...over just seconds sometimes. Dunno (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: External supply for RCX
|
|
(...) I've been using rechargable Eveready Renewals in one of my RCX's for quite a few months without any problems... I think it is the lower 1.2 volt compared to the 1.5V of a standard battery that they are concerned with. Dave (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: IR Ball (was Soccer-Playing Robots)
|
|
(...) That is right. It's not only a mere problem of area covering, but the main objective is to have the robot locate the ball quite quickly without a significative error. We tried at first with the same ball and less LEDs and it was working, but (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | RE: IR Ball (was Soccer-Playing Robots)
|
|
Thanks! I _do_ get into toy stores fairly often ... but generally ignore stuff at the register and normally go straight to the Lego aisle. :) Doug Wilcox Senior Web Developer iMcKesson Provider Solutions Group-Needham 160 Gould Street, Suite 130 (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | RE: IR Ball (was Soccer-Playing Robots)
|
|
I suspect (but am trying to confirm) that the high number of LEDs was not just to increase the area covered, but the luminosity as well. (Can one use the term _luminosity_ for IR if it's outside our visible spectrum?) The "brighter" the ball in IR (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|
| |
 | | Re: IR Ball (was Soccer-Playing Robots)
|
|
>That wouldn't look as great as a free rolling ball - and the >robots would perhaps have trouble finding it while it's in >motion....but 28 LEDs is a heck of a lot! Seems like a lot to me. The wider angle IR LEDs have a 60 degree cone. I think you (...) (26 years ago, 1-Sep-00, to lugnet.robotics)
|