 | | Re: Pneumatics and its uses
|
|
(...) Sounds good! I checked out the Clippard home page and I can't find the valves you are referring to. Nor can I find any relevant EBay auctions. Do you have any more info? One thing that I tried is running the bot off liquified gas. CFC's would (...) (26 years ago, 11-Jul-00, to lugnet.robotics)
|
| |
 | | Re: Handyboard startup problems
|
|
Yes, I encounter something similar. Do you use servo on your board? I also have some trouble with the motor ports. I am not sure what causes it. I also have trouble with the motor ports. When I run the motor at 50% power (back or forward), both red (...) (26 years ago, 10-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Expanding the available input/output ports of the RCX
|
|
in article NEBBIHKHBKAFAGKCCILO...s@olf.com, Ram Meenakshisundaram at rmeenaks@olf.com wrote on 7/7/00 9:58 AM: (...) I am a Lego purist, so I don't want to modify my pieces. Of course, if Lego ever creates an official multiplexer, I'll probably get (...) (26 years ago, 10-Jul-00, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
 | | H2000 optical position sensor
|
|
Hi, I am planning to build a position detector with a H2000 chip. The chip is used in several optical mice, for example the H2000/0006 can be found inside the Microsoft IntelliEye mouse. I sill have difficulties in finding the manufacturer and the (...) (26 years ago, 10-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | LegOS on LinuxPPC
|
|
I recall somebody writing to this list about a problem with LegOS under LinuxPPC, and the message seemed to imply that things were mostly happy. I can't make the compiler compile. I'm using gcc 2.95.2. The make proceeds for a good while, then I get (...) (26 years ago, 10-Jul-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Handboard supplier?
|
|
Try Patrick Hui at Robot Store ( (URL) or for info emailto:info@RobotStoreHK.com ) he sells assembled boards at reasonable prices. (...) (26 years ago, 10-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Expanding the available input/output ports of the RCX
|
|
Ram Meenakshisundaram schreef: (...) You could use the sensors that came with the Cybermaster kit, they have a built-in resistor so it should be possible to hook up two of those on one input port and by using RAW values see which switch is pressed. (26 years ago, 10-Jul-00, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
 | | serial communications HB - PC
|
|
Hi! I need to know how implement a serial and asyncronous communication (send and recieve data between my PC and my HB) through the computer conector (not through the spi!), Does somebody know how can i do it or what are the hb serial commands or (...) (26 years ago, 9-Jul-00, to lugnet.robotics.handyboard)
|
| |
 | | RE: Expanding the available input/output ports of the RCX
|
|
Sure you can try using just three input/output ports, but eventually you end up scaling back you designs. Of course, you can always buy another RCX to increase the number of ports, which will throw you back $200. Adding a multiplexor is such an easy (...) (26 years ago, 9-Jul-00, to lugnet.robotics, lugnet.robotics.rcx)
|
| |
 | | four polariod sonars
|
|
Hi everybody! I´m working in mi mobile robot and for the navigation i want to connect 4 polaroid sonars to my HB, has anybody developed any design? I found in the HB site a multiplexor circuit for connect 4 sonar by adam cox, but i can´t find more (...) (26 years ago, 9-Jul-00, to lugnet.robotics.handyboard)
|