To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *22184 (-10)
  Re: 9v Gear Motors
 
I am very surprised to learn that the coded speed control function actually uses "on" and "off" rather than "on" and "float". When the motor is turned "on", it speeds up, consuming substantially more power than it will once it reaches its final full (...) (26 years ago, 9-Jun-00, to lugnet.robotics)
 
  Re: 9v Gear Motors
 
=>From: "Jerry Kalpin" <jdkalpin@sympatico.ca> =>... =>if there are three states: on, off and float, there must =>be more than 2 terminals in use. No, with two terminals (A & B), you can get: * A positive with respect to B => motor runs in one (...) (26 years ago, 9-Jun-00, to lugnet.robotics)
 
  Re: 9v Gear Motors
 
Conrad, if there are three states: on, off and float, there must be more than 2 terminals in use. Yes, there is PWM. According to the experts that changes the torque more than the speed. Under no load and a setting of (say) 2 you should see little (...) (26 years ago, 9-Jun-00, to lugnet.robotics)
 
  Re: SDL and legOS (was: memory left)
 
Luis Villa <liv@duke.edu> wrote in message news:960488287.393fe...uke.edu... (...) productive, (...) Well, it depends of course on what you intend to do with it. If you for example design and implement a protocol of some sort, it's a great (...) (26 years ago, 9-Jun-00, to lugnet.robotics.rcx.legos)
 
  two questions
 
Hey, everybody. I have two questions, most of which probably can't be understood by most of the readers on this list :( 1) Is there any way that the stack size might be miscalculated by the new, improved makelx? I've experienced a problem where a (...) (26 years ago, 9-Jun-00, to lugnet.robotics.rcx.legos)
 
  Motor Masks***
 
Hi , does anyone know if there are specific moter masks already defined for the HB? Or can I just initialize them anywhere there is free memory? Thanks -Mike (26 years ago, 9-Jun-00, to lugnet.robotics.handyboard)
 
  Re: lcd_refresh()- get rid of it?
 
Then I'll put a note in to that effect- can't believe I hadn't noticed that earlier. There are a couple of bugs in config.h, too (in the CONF_X depends on CONF_Y) sections, so I'll just check something in later. Nothing big, just irritating :) -Luis (...) (26 years ago, 9-Jun-00, to lugnet.robotics.rcx.legos)
 
  Re: lcd_refresh()- get rid of it?
 
"Luis Villa" <liv@duke.edu> wrote in message news:FvuEJE.F7I@lugnet.com... (...) Well, it depends on the line: #define CONF_LCD_REFRESH in file boot/config.h. If you comment it out, you still need lcd_refresh()... :-) Bye, Paolo. --- "The pessimist (...) (26 years ago, 8-Jun-00, to lugnet.robotics.rcx.legos)
 
  using the <remote> commmand in NQC
 
Does anyone know where I can find a listing of the 4 digit codes for the <remote> command? Thx, Brandon (26 years ago, 8-Jun-00, to lugnet.robotics.rcx)
 
  Re: 9v Gear Motors
 
Just went back and re-read the book, and in fact the RCX does do pulse width modulation and not voltage amplitude to set different power levels. In which case I'm not sure why effectively doing the same thing in NQC code works any better, but it (...) (26 years ago, 8-Jun-00, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR