To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *2211 (-10)
  Re: clueless programmer
 
A very simple program which will exercise the motors in this configuration is listed. The first section will put a message on the LCD then wait until the sopt button is pressed. Once the stop button is sensed, it will turn on the motor in port 0. (...) (29 years ago, 26-May-97, to lugnet.robotics.handyboard)
 
  TEAC Stepper motor
 
Has anyone had any experience driving the stepper motor from a TEAC 5 1/4 in floppy drive with the HB. I have been going through Jones' tutorial on stepper motos and have decided that the motor is a permanent magnet, 4 winding variable reluctance (...) (29 years ago, 26-May-97, to lugnet.robotics.handyboard)
 
  RE: IC 3.1
 
also, joe... there are several programs you can run to get more conventional memory (640)... dos 6.0 to 6.22 comes with memmaker... run this a couple times, toy with the settings a bit to see what you can pull off... one of the settings may cause (...) (29 years ago, 26-May-97, to lugnet.robotics.handyboard)
 
  Motors: Please help! Going out of my mind...
 
Please somebody help! Actually it's not quite that bad, but I've been searching and hunting trying to find some motors to use for a new robot base. Does anyone have any suggestions for where to find motors with gearboxes that can carry a few pounds (...) (29 years ago, 25-May-97, to lugnet.robotics.handyboard)
 
  clueless programmer
 
Ihave only been working with my HB for a few weeks but the coding appears pretty easy. I'll be happy to help/teach you C. Which ports are the motors and touch sensor connected to. (...) (URL) (...) else for that matter. (...) Tutebot from (...) (...) (29 years ago, 24-May-97, to lugnet.robotics.handyboard)
 
  futaba compatible servos
 
hi... i'm coreyfro, (hi coreyfro) and i'm totally new to this... i'm a junior-programer/ele...-addept(or addict)/new-toy-junky i was drawn here via the lego aspect, but that is not my cocern now... i have buckets of radio controlled car junk at my (...) (29 years ago, 24-May-97, to lugnet.robotics.handyboard)
 
  clueless programmer
 
First time I have wrote to the list hope it goes well... To be honest I don't have a clue on how to program in 'C' or any thing else for that matter. But I'm slowly learning. I want to write a program similar to that of the Tutebot from the "Mobile (...) (29 years ago, 23-May-97, to lugnet.robotics.handyboard)
 
  Nitintol wire
 
I am in need of a small amount (5inches) of that wire that changes shape when applied heat. (200F). Anyone know where I can get a small quanity very fast. thanks (29 years ago, 23-May-97, to lugnet.robotics.handyboard)
 
  RE: weird headers
 
(...) Thanks, I stuck a pot in it's place and fiddled with it until I got 4.49k and it worked great. I came up with the 4.49k by taking 1/x*.0068 = 32.75. Where .0068 is the cap, and 32.75 was my desired frequency. So x was determined to be 4.49 (...) (29 years ago, 23-May-97, to lugnet.robotics.handyboard)
 
  Re: IR
 
Hi Fred, I do not know exactly of your situation with the IR detector/emitter arrangement. I found that it sometimes picks up noise occassionally. I also found that with small resister in the range that you are using (330ohms), the range is too much (...) (29 years ago, 23-May-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR