 | | Re: [min-max] command gets no respect...
|
|
in article 200006011157.EAA1130...hlink.net, pmunce at lego-robotics@crynwr.com wrote on 6/1/00 4:57 AM: (...) Actually the speed doesn't change very much. The main difference you will notice is in the power of the motor - hence the name of the (...) (26 years ago, 1-Jun-00, to lugnet.robotics)
|
| |
 | | Re: using polarity switch as a rotation counter
|
|
in article FvGo0v.961@lugnet.com, mike fusion at tltpj@uwm.edu wrote on 5/31/00 10:46 PM: (...) I had the idea a while back but haven't done anything with it yet. Let us know how it works out. (...) They're sort of hard to turn. Gearing them up to (...) (26 years ago, 1-Jun-00, to lugnet.robotics)
|
| |
 | | Re: Major breakthrough serial wise.
|
|
in article 39365A56.86986217@nexen.com, Steve morris at smorris@nexen.com wrote on 6/1/00 5:43 AM: (...) Try posting this on a more general list if the following suggestions don't help: 1) put the RCX and tower underneath a box to block out all (...) (26 years ago, 1-Jun-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Re: Rapidly moving plastic and rubber...
|
|
That is the coolest thing I have seen in months. Was it painful? Great invention. -- Bob Fay rfay@we.mediaone.net The Shop (URL) Reid" <kpreid@ibm.net> wrote in message news:1ebjoeu.1h4xnb8...ibm.net... (...) (26 years ago, 1-Jun-00, to lugnet.technic, lugnet.robotics.rcx)
|
| |
 | | Re: RCX 1.5 to 1.0
|
|
(...) The only difference between the two units is a slight board change and the case is lower and is MISSING the power adapter port. So the 1.0 is more desired. Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (26 years ago, 1-Jun-00, to lugnet.robotics)
|
| |
 | | Rapidly moving plastic and rubber...
|
|
What moves at 12 ft/sec _on_the_ground_ and is built entirely out of LEGO parts? This: (URL) (26 years ago, 1-Jun-00, to lugnet.technic, lugnet.robotics.rcx)
|
| |
 | | Major breakthrough serial wise.
|
|
I have been fiddling with serial interrupts with little success. Today I finally figured out that interrupts are masked in the CCR until you run the word RCX_INIT. I was blindly assuming that interrupts were generally enabled and I only had to deal (...) (26 years ago, 1-Jun-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | [min-max] command gets no respect...
|
|
i just rec'd my ris1.5 and am finding the the rcx will not respect the 'set abc power [min-max]' command. should i expect the motors that came supplied to vary their speed using this command or is this command reserved for other motors? (...) (26 years ago, 1-Jun-00, to lugnet.robotics)
|
| |
 | | What difference between RCX 1.0 and RCX 2.0
|
|
Dear sirs, who could make description about RCX 1.0 and RCX 2.0 . thanks Wanshone Chiou 6/1 2000,Taiwan ___...___ pchome §K¶O¹q¤l«H½c¡A¥Ó½Ð½Ð¦Ü: (URL) (26 years ago, 1-Jun-00, to lugnet.robotics)
|
| |
 | | using polarity switch as a rotation counter
|
|
I don't know if anyone has used this yet but I found that I can use the polarity as a raw rotation counter with four positions, 2 off and two on. if geared down with a worm gear you can get 8 rotations per turn and more, well you get the idea. just (...) (26 years ago, 1-Jun-00, to lugnet.robotics)
|
| |
 | | Re: RCX 1.5 to 1.0
|
|
Andy Gombos wrote ... (...) The 1.0 and 1.5 firmware are identical. -- Mark Haye, mark_haye(@)tivoli(.)com IBM TSM Server Development, Tucson, AZ (26 years ago, 1-Jun-00, to lugnet.robotics)
|
| |
 | | Re: XC68HC11F1B4 Pin assignments
|
|
in article 393601FD.1DF@hemo.net, Zele at 4n7ax@hemo.net wrote on 5/31/00 11:26 PM: (...) I found the documentation for the MC68HC11F1 series on the Motorola web site at this URL: (URL) documentation is in an 848k PDF file: (URL) picture you're (...) (26 years ago, 31-May-00, to lugnet.robotics, lugnet.robotics.handyboard)
|
| |
 | | 0.5 degree resolution with rotation sensor
|
|
Hi guys! I've been playing with a position controller and thought that could interest someone else. Since the rotation sensor has only 16 counts for 1 full turn, which means 22.5 degrees, I thought about a way to get some more precision. In order to (...) (26 years ago, 31-May-00, to lugnet.robotics)
|
| |
 | | RCX 1.5 to 1.0
|
|
If you buy an RCX 1.5, but want a 1.0, can you just download 1.0 firmware to make it a 1.0? Thnx, Andy (26 years ago, 31-May-00, to lugnet.robotics)
|
| |
 | | XC68HC11F1B4 Pin assignments
|
|
Hello, I have few XC68HC11F1B4 in 64-pins plastic SDIP, but can not find any data about pin assignments for this chip. Can somebody to help me with it ? Please e-mail to: 4n7ax@hemo.net Z. Ristic (26 years ago, 31-May-00, to lugnet.robotics.handyboard)
|
| |
 | | XC68HC11F1B4 Pin assignments
|
|
Hello, I have few XC68HC11F1B4 in 64-pins plastic SDIP, but can not find any data about pin assignments for this chip. Can somebody to help me with it ? Please e-mail to: 4n7ax@hemo.net Z. Ristic (26 years ago, 1-Jun-00, to lugnet.robotics, lugnet.robotics.handyboard)
|
| |
 | | Re: NQC 2.2 a2
|
|
(...) I'm really busy recently; it'll probably be a few more days before I have the Linux builds done. (Since it's an alpha release, it doesn't make my top priority list. I'll drop everything for the final release. *grin*) (26 years ago, 31-May-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Grizz, Let me know.
|
|
Hi Let me know if you get this message so I know if we are on the same list? Thanks -Mike (26 years ago, 31-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Expansion board question?
|
|
Hi I added the expansion board to my HB. I dowloded the propper files and My question is how do I check to see if my expansion board is working and has the files it needs? Thanks! -Mike (26 years ago, 31-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: serial number
|
|
Well, the purpose would be that it would save me the trouble of recompiling the kernel every time I have to download to a new RCX. I might end up with as much as 8 of them. Other than that, I was just curios. Torkel Luis Villa <liv@duke.edu> wrote (...) (26 years ago, 31-May-00, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|