To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *22054 (-10)
  XC68HC11F1B4 Pin assignments
 
Hello, I have few XC68HC11F1B4 in 64-pins plastic SDIP, but can not find any data about pin assignments for this chip. Can somebody to help me with it ? Please e-mail to: 4n7ax@hemo.net Z. Ristic (26 years ago, 1-Jun-00, to lugnet.robotics, lugnet.robotics.handyboard)
 
  Re: NQC 2.2 a2
 
(...) I'm really busy recently; it'll probably be a few more days before I have the Linux builds done. (Since it's an alpha release, it doesn't make my top priority list. I'll drop everything for the final release. *grin*) (26 years ago, 31-May-00, to lugnet.robotics.rcx.nqc)
 
  Grizz, Let me know.
 
Hi Let me know if you get this message so I know if we are on the same list? Thanks -Mike (26 years ago, 31-May-00, to lugnet.robotics.handyboard)
 
  Expansion board question?
 
Hi I added the expansion board to my HB. I dowloded the propper files and My question is how do I check to see if my expansion board is working and has the files it needs? Thanks! -Mike (26 years ago, 31-May-00, to lugnet.robotics.handyboard)
 
  Re: serial number
 
Well, the purpose would be that it would save me the trouble of recompiling the kernel every time I have to download to a new RCX. I might end up with as much as 8 of them. Other than that, I was just curios. Torkel Luis Villa <liv@duke.edu> wrote (...) (26 years ago, 31-May-00, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
 
  Re: light sensor
 
<lego-robotics@crynwr.com> wrote in message news:38.69033b3.2664...aol.com... (...) (URL) (26 years ago, 31-May-00, to lugnet.robotics)
 
  Re: serial number
 
As far as I know, there is no way to access it. Why? If you intend to use it for unique identification for networking purposes, you can go into the config files in legOS and change the network address there... Luis (...) ---...--- "Going to (...) (26 years ago, 31-May-00, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
 
  Re: Newbie question
 
I would also suggest you take a look at Gordons Brick Programmer. It is a convenient intermediate between the Lego RCX Code and NQC. Typical prototyping time is 10 - 15 minutes. It's a great way to check stuff out. I would also strongly suggest the (...) (26 years ago, 31-May-00, to lugnet.robotics)
 
  serial number
 
There is a serial number printed on the RCX. Is it possible to access that serial number through the hardware, or is it only printed on the outside? Torkel (26 years ago, 31-May-00, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
 
  Re: Newbie question
 
(...) If you enjoy programming, get RIS. If you hate programming, get RDS. If you're not sure if RIS is for you, go to your local bookstore and buy or browse Dave Baum's Definitive Guide to LEGO MindStorms. It should give you a feel of how long it (...) (26 years ago, 31-May-00, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR