To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *21934 (-10)
  Re: Forth question
 
(...) Actually the various reasons are simple so I might as well state them. The serial port is not available at the time I want to create a constant because the serial port will be broken and therefor can't be used as the forth input stream. I am (...) (26 years ago, 24-May-00, to lugnet.robotics.rcx.pbforth)
 
  Re: Forth question
 
(...) I still want to create a constant from within a definition. I have an initializing word that will calculate the value of the constant. For various reasons I can't do this calculation except within the runtime behavior of the word. This is not (...) (26 years ago, 24-May-00, to lugnet.robotics.rcx.pbforth)
 
  Re: GA in RCX
 
(...) Yes. Therefore you might want to use the truncation selection, which allows you to have only 1 copy of the population at a time to save memory. It worked for us, we have a small GA running inside of the RCX. We evolved a program with simple (...) (26 years ago, 24-May-00, to lugnet.robotics.rcx.legos)
 
  RE: Forth question
 
(...) 1 CONSTANT ONE Recall that CONSTANT is a *defining* word, just like the ":" It makes a name in the dictionary, in this case "ONE" and then links to a special bit of code that is executed every time ONE is interpreted. It grabs the value out of (...) (26 years ago, 24-May-00, to lugnet.robotics.rcx.pbforth)
 
  Forth question
 
I'm trying to define a constant in a compiled word. : zzz 1 CONSTANT ONE ; I know its not right. It tries to compile "ONE" which is not what is wanted. What is the right way to say this? (26 years ago, 24-May-00, to lugnet.robotics.rcx.pbforth)
 
  Re: RTC
 
(...) Yes. The IR just becomes a dumb serial port whith an annoying builtin echo, almost like you had a serial port cable attached to the RCX. Open the port on the host system using whatever language you want and proceed to send commands to it. Of (...) (26 years ago, 23-May-00, to lugnet.robotics.rcx.pbforth)
 
  servos again
 
I'm still at my servo question :) the 3 servo routines so far use "normal" digital outputs. There are, according to the FAQ, 4 extra outputs I could use (SPI J6). Does this mean that I could write my own routines to drive 4 extra servos using these (...) (26 years ago, 23-May-00, to lugnet.robotics.handyboard)
 
  Re: RCX Commincations
 
Colin- You may want to look through the past fews days worth of discussions in lugnet.robotics.rcx.legos. There has been quite a bit of back and forth about a few summer projects that people will be working on, including one with six robots and (...) (26 years ago, 23-May-00, to lugnet.robotics)
 
  Re: GA in RCX
 
(...) I like that spirit :) (26 years ago, 23-May-00, to lugnet.robotics.rcx.legos)
 
  Re: GA in RCX
 
(...) You will be. You will be... :) Tobias (26 years ago, 23-May-00, to lugnet.robotics.rcx.legos)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR