 | | Re: Quick Q : 9v Motors
|
|
(...) There's a big difference - some of the details are here: (URL) Baum (26 years ago, 20-May-00, to lugnet.robotics)
|
| |
 | | Re: IR communication PC <-> brick with NQC
|
|
(...) The RCX uses a special packet protocol which involes a lot of binary (non-ASCII) bytes, so controlling it with Hyperterminal won't work very well. Your best bet is to either write your own code to send the packets of the serial port or just (...) (26 years ago, 20-May-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Is there a compatible h8 assembler for forth words?
|
|
(...) A good rule. I just know I'm going to need fast so I am planning ahead. Somehow I'm usually at the bleeding edge of trying to squeeze everything possible out of limited hardware. I originally learned my Forth on a 68000 (Mac Forth on the (...) (26 years ago, 20-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: Spirograph Formulas??
|
|
You might enjoy the book "Turtle Graphics" - (URL) - uses the Logo language to control robotic turtles - descibes everything not in the mathematics of analysis but in terms of local geometric movement. Not sure if it has spirograph in it or not, but (...) (26 years ago, 19-May-00, to lugnet.robotics)
|
| |
 | | RE: Is there a compatible h8 assembler for forth words?
|
|
(...) No there is not. That being said, it's pretty easy to write one...if you have the time. I fiddled around with it a bit and then gave up since the GNU tools worked pretty quick. It was strictly a time/value exchange. From bitter experience, (...) (26 years ago, 19-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Re: Is there a compatible h8 assembler for forth words?
|
|
(...) I don't think this is clear. I ment an assembler written in pbforth that can create assembler defined words in the RCX (26 years ago, 19-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Is there a compatible h8 assembler for forth words?
|
|
I asked this once before but in the middle of an unrelated email so the question got lost. (26 years ago, 19-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | DJGPP GNU cross compiler tools
|
|
It looks like my ISP has changed their policy about anonymous ftp and now allow it. I've placed the DJGPP port of the GNU tools on my website here: (URL) It's a 5 meg download. Please let me know if you have any problems downloading this file. I (...) (26 years ago, 19-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | multiplex other analog ports than analog 0 & 1
|
|
(...) These two (...) ports. (...) I built the Expansion board in order to control servos. I cannot use the additional analog inputs because I have destroyed analog port 0 and 1. Is it possible to multiplex other analog ports? What software changes (...) (26 years ago, 19-May-00, to lugnet.robotics.handyboard)
|
| |
 | | RE: hforth register usage
|
|
(...) Right. If you look at the beginning of h8hforth.asm, I've abstracted the actual register names so I could move them around....here's the snippet from the file... ; The H8/300 Forth machine register usage has to be closely intertwined with ; (...) (27 years ago, 19-May-00, to lugnet.robotics.rcx.pbforth)
|