To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *21789 (-10)
  RE: New pbForth GUI
 
(...) Great! Maybe I can get another convert over to the dark side... The script uploads should work well too. And definitely try the SAVE-SYSTEM download. You need to load bigsys.srec firmware. Just type SAVE-SYSTEM after you've added whatever (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
 
  RF vs IR link
 
Just a naive question: How much difficult would be to use the RF Cybermaster link with the RCX? (27 years ago, 17-May-00, to lugnet.robotics.rcx)
 
  Re: lnp communication question
 
Remember the medium... cheap IR basically stinks for transmission. You get transients from the lights in your room, the outdoors, yadda, yadda. Luis (wishing for RF like the Europeans get ;) (...) ---...--- "Going to California with an aching in my (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.legos)
 
  Re: New pbForth GUI
 
(...) Just to confirm that, I successfully installed the GUI in my NT system (NT4.0 Build 1381, SP 5) following Jeff's procedure. It works great, no need of the giveio driver, no problems with the COM port though not having the Admin rights. Thanks (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
 
  RE: how to drive extra steppers with handyboard
 
i ended up using two SSC II's to control the twelve servos on my robot because most of the time the servos connected to the XB would not work. the SSC II servos worked almost all the time. (URL) think this is the web address and the SSC II's connect (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
 
  RE: New pbForth GUI
 
Jeff wrote... (...) Thanks Jeff, I was worried it might be taken the wrong way after I posted it... (...) I've snipped the rest of the description, but the result is that it works without the giveio driver, if I understand correctly. This is VERY (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
 
  RE: how to drive extra steppers with handyboard
 
Try Scott Edwards SCC II Servo controller. (...) This message is for the named person's use only. It may contain confidential, proprietary or legally privileged information. No confidentiality or privilege is waived or lost by any mistransmission. (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
 
  Expansion board cannot handle more than 2 servos
 
Hello, Reading the discussion on servos recently, I thought I'd share this info with you. I have advised a few student group projects involving servos and the XB and came to the conclusion that the XB cannot handle more than two or so servos. The (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
 
  Re: Scout, Microscout & IR Remote
 
Dennis Williamson <dennis.NO@SPAM.netstrata.com> wrote (...) You're right. Sorry, my fault. There had been so much talking about this feature between the end of 1999 and the beginning of 2000 that I thought Eric's page included this info too, and (...) (27 years ago, 17-May-00, to lugnet.robotics)
 
  RE: how many servos on handyboard?
 
Remeber also that you have to cut the motor power trace and use an external 5V source for the motors in this case. The HB itself will output 9.6 V from the motor ports. (...) This message is for the named person's use only. It may contain (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR