 | | Re: lnp communication question
|
|
Hello Tobias, (...) Why do you think there's only 1 byte that can be sent? If your data buffer is longer, bytes are sent one-by-one serially in a packet... (...) look into lnp.c and you will see that both lnp_integrity_xxx and lnp_addressing_xxx are (...) (27 years ago, 15-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: serial port interrupts
|
|
(...) Actually that's what I was intending but I couldn't remember the words at my keyboard. To make debugging easier I will use parallel words that can be merged in later. I was going to use the following debugging strategy: Put the isr init in a (...) (27 years ago, 15-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | due to popular demand
|
|
The HOWTO and other legOS archives will be available (until I get it to sourceforge) at (URL) for the people who wrote and volunteered to serve it- the archives now total something like ~100 meg (several different copies of compilers are in there) (...) (27 years ago, 15-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: ideas for a RIS 2.0
|
|
All I'd ask of an RIS 2.0 is a huge bank of inputs and a huge bank of outputs. 3 of each is just not enough. Kerry -- ===...=== Dr Kerry Raymond, Distinguished Research Fellow kerry@dstc.edu.au CRC for Enterprise Distributed Systems Technology Ph: (...) (27 years ago, 15-May-00, to lugnet.robotics)
|
| |
 | | Re: using 3v motors?
|
|
In theory yes. Since the motor will be powered by the aux power supply only, as long as it is at 3 volt, it should be OK. (am I right, Prof. Martin?) -- Ray Wayne Crosbie <wcrosbie@home.com> wrote in message news:FuKHs7.B7v@lugnet.com... (...) 400 (...) (27 years ago, 14-May-00, to lugnet.robotics.handyboard)
|
| |
 | | RE: hellofriend
|
|
Yes, definitely spam! | -----Original Message----- | From: Meabadboy@aol.com [mailto:Meabadboy@aol.com] | Sent: Sunday, May 14, 2000 3:48 AM | To: handyboard@media.mit.edu | Subject: Fwd: hellofriend | | | SPAM??? | | (27 years ago, 14-May-00, to lugnet.robotics.handyboard)
|
| |
 | | using 3v motors?
|
|
Is there any way to use 3 volt motors on the Handyboard? They draw about 400 ma. Using a series resistor of about 10 ohms works, but it will have to be about 5 watts, consuming a lot of power needlessly. The FAQ shows how to run 6-36v motors through (...) (27 years ago, 14-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Scout, Microscout & IR Remote
|
|
My son and I accidently discovered last night that if the Microscout light link input is in range, or fiber optically connected, to the Scouts light link output, then the infrared remote (from the UA kit) "C" buttons can then control the Microscout (...) (27 years ago, 14-May-00, to lugnet.robotics)
|
| |
 | | lnp communication question
|
|
Hi! When using lnp_integrity_write(&data, length), what is the length argument used for? The data can only be one byte long if I understand it correctly. Can I use the length argument to send an additional byte of information? Is there anyway I can (...) (27 years ago, 14-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | RE: serial port interrupts
|
|
(...) Sounds good Steve, see notes below for some pointers... (...) Absolutely. All we have to do is enable the interrupts on the receiver throw the chars into a buffer. I'd keep the standard FORTH words that already exist so less system source (...) (27 years ago, 14-May-00, to lugnet.robotics.rcx.pbforth)
|