To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1896 (+10)
  Somewhat C challenged.
 
Please excuse my bitwise ignorance. Could someone explain this statement to me. if (4 & peek(0x1000)) what does peek(0x1000) return? what is the 4 for ? and what does the "&" compare? thanks victor (30 years ago, 9-Apr-97, to lugnet.robotics.handyboard)
 
  MORE IR
 
I am going blind reading the archives for the solution to this problem so I will just ask. Ive got a Radio Shack tin can IR reciever plugged into digital(7). An High output IR LED w/ current limiter resistor in series (LED was getting quite warm) (...) (30 years ago, 9-Apr-97, to lugnet.robotics.handyboard)
 
  Re: sonar hookup
 
If I recall correctly, I think the BINH in the sonar software is set high for the entire duration of the ping. This way, ECHO will never trigger. If you tie your BINH to GND, it will enable ONLY the internel blanking. ---...--- ericson mar Master of (...) (30 years ago, 9-Apr-97, to lugnet.robotics.handyboard)
 
  hb_ir.c
 
In the hb_ir.c and the hb2_ir.icb Regaring ir_counts(4) what ports is this using. digital(?), analog(?)? What is it counting? (30 years ago, 9-Apr-97, to lugnet.robotics.handyboard)
 
  (no subject)
 
Hello! Just 1 thing today: 1. Is there any sort of chip that can be wired up to the HB's motor ports, and then convert it to 16 (or less, maybe) outputs? phil thehahns@nconnect.net PS: does anyone know of any robot designs that will allow a robot to (...) (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
 
  Re: Somewhat C challenged.
 
Victor, The peek(0x1000) statement returns the byte at memory location 1000 (hex). In C, the '&' operator is a bitwise AND. So, what you are doing is ANDing 4 and the contents of 0x1000. What's really going on is you are interested in only bit 3 (...) (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
 
  IR in programs
 
How would I use an if/then statement if I used the onboard IR reciever? Earlier, I downloaded a program that Max Davies wrote to determine the different variables for my remote. In the readme file, it says that the rules are set by a command like (...) (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
 
  voltage divider
 
could the voltage divider circuit shown in the Mobil Robots book (page 116 fig5.20b) be implemented as is OR does the built in pulldown resistors cause it to be modified. Thanks for all the brain dumps, victor (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
 
  NOTE 04/10/97 10:50:15
 
Hi, Can someone help me understand encoders.asm? This is what I deduced from the code and I'm wondering if my guess is correct. 1. When TIC3 and TIC2 inputs are changed, an "interrupt" in execution occurs and and execution immediately jumps to the (...) (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
 
  Re: IR in programs
 
(...) Here is a simple example of how to do 'different things' when you press various buttons on your remote. If you press digits, they are displayed on the LCD. If you press rewind, the LCD is cleared. When you press stop, the program ends. If you (...) (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR