To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1881 (+10)
  Re: pressure sensors..
 
Try www.infusionsystems.com. Let me know if they are able to fill the need. Thanks. ---...--- Adam B. Cox check out my web page Computer Engineer (URL) Communications Corp. vmail: 416-241-7000 (x224) ---...--- (...) (30 years ago, 8-Apr-97, to lugnet.robotics.handyboard)
 
  Re: ??? Last minute sanity checking for a new board
 
this is basically right, read the "appendixb" document listed on the tech docs page for this kind of info....... re: hb board size, it's sized so it will fit into a commercial plastic enclosure that holds an 8 cell AA battery pack. -fred (URL) your (...) (30 years ago, 8-Apr-97, to lugnet.robotics.handyboard)
 
  Sony IR
 
Could someone tell me what the signal from a sony remote looks like (freq, period, etc and how it is read by the sony-ir program distributed with IC) Thanks!! Tom (30 years ago, 9-Apr-97, to lugnet.robotics.handyboard)
 
  Re: pressure sensors..
 
(...) Hi James , What sort of Pressure sensor are you looking for ? air Pressure , Water ? let me Know , i work for Motorola Semiconductor we have a few avaliable let me Know via the list or return email Regards Bruce Given Montreal, Quebec, Canada (...) (30 years ago, 9-Apr-97, to lugnet.robotics.handyboard)
 
  Re: pressure sensors..
 
James, You can get Forse Sensing Resistors,and you can use strain gauages, but I find the easies thing is to make a bag or balloon of the shape you want, connect a tube to it, and use a small air pressure sensor. These are very cheap and readily (...) (30 years ago, 9-Apr-97, to lugnet.robotics.handyboard)
 
  Re: running 2 IR
 
What you can do is just like the schematic for the built-in IR emitter circuit. You need to either software generate your wave or do it like the schematic. If software generated, this output would come from a output port on the HC11 to a transistor (...) (30 years ago, 9-Apr-97, to lugnet.robotics.handyboard)
 
  Re: running 2 IR
 
(...) Can we not tie two IR LED's in parallel and plug into the IR port on the HB. ? (...) (30 years ago, 9-Apr-97, to lugnet.robotics.handyboard)
 
  Re: pressure sensors... antistatic foam
 
A viable option, depending on what sort of pressure is involved, is to put a thin piece of conductive (ie. antistatic) foam between two metal plates. The resistance between the plates ends up being roughly proportional to the pressure applied. It (...) (30 years ago, 9-Apr-97, to lugnet.robotics.handyboard)
 
  Re: pressure sensors..
 
JM, I don't have the book in front of me but Mobile Robots, From Inspiration to Implementation has some info on just this subject. If you don't have it or can't get access to it let me know and I'll do some research for ya. For example if its touch (...) (30 years ago, 9-Apr-97, to lugnet.robotics.handyboard)
 
  Re: running 2 IR
 
If the IR LEDs both add up to a current requirement of 800ma (the spec on the ztx614) then yes you should be able to. You may want to add a resistor to supply that assures you don't get more than 800ma from supply (if that is Imax for those LEDs). (...) (30 years ago, 9-Apr-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR