 | | Thanks to Chuck and Max
|
|
Thankyou to Chuck and Max for the help with writing this code for reading square wave frequencies.If anyone else can use it here it is.Be careful though it resets the board every few seconds.I think that if this is a problem you could probably (...) (30 years ago, 31-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: AS11
|
|
DB - Define Byte ; allocates one byte of storage with initial value specified DW - Define Word ; allocates two bytes of storage with initial value specified (...) ---...--- Maria Pirsic IEEE Branch Treasurer 96/97 Carleton University (...) (30 years ago, 31-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | where to get screens
|
|
Does anyone know of a place to order LCD screens? I usually ordered them from Mouser but apparently the manufacter has discontinued that line. A would appreciate any help as to where to order them. Thanks in advance... (30 years ago, 31-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: your mail
|
|
(...) The chip you are really interfacing with here is the HD44780 controller on the back of the lcd. It has a character set and a register. You write the register and the controller displays the appr. member from its char. set. There is some (...) (30 years ago, 31-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: AS11
|
|
(...) DW - Define word (intel assembler) FDB - Form Double Byte Constant (motorola assembler) Example: (in HC11 memory order) ORG $100 DW $1234 DW $5678 Memory dump start at address $100, you will find: Address Data $0100 $12 $0101 $34 $0102 $56 (...) (30 years ago, 31-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Digital Outputs
|
|
(...) Adam, Have you thought about using a some of the Motor Chip driver digital output lines(if you don't need two motor driver chips)? If you pull one of the L293 chips you can free up 4 digital output lines very easily. It would, of course, (...) (30 years ago, 31-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | re: IR frequency / o'scope adjustments
|
|
(...) You want to trigger off of the signal, or maybe the line; the knobs to turn are generally marked "slope" and "level" or something close to this. I usually use a positive slope, I just like the signal to be going in a positive direction at the (...) (30 years ago, 31-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | LM2931
|
|
Is it allright if I replace the LM2931 on the Handyboard Interface/Charger Unit with 78L05 (same package)? (30 years ago, 31-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | connecting Scott edwards mini-ssc to handy board
|
|
Hi, Does anyone have any insight to offer on connecting the HB to the scott edwards electronics mini-ssc servo controller? I wanted to connect directly to the HB through the onboard rj12 jack. Looking at the schematics It seems I might be able to (...) (30 years ago, 31-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Servo encoder.
|
|
Does anyone see a problem with using the pot in a modified servo and an encoder. I have modified it so that it makes contact once every revolution. Would this mechanical contact create any "bounce" that would interfere with the enoding ticks. (30 years ago, 31-Mar-97, to lugnet.robotics.handyboard)
|