 | | Re: Sonar and the handyboard
|
|
Hi, with all this talk of sonar, I thought I finally get to hooking mine up. All I get is 8". If I unplug it, I get 0". I'd swear I have it hooked up right. Someone sent out a mail earlier this week, and I had mine hooked up just like it said. I (...) (30 years ago, 20-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Sonar and the handyboard
|
|
Tom, Are you hearing a ticking sound coming from the transducer? Let me know. (...) (30 years ago, 20-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Sonar and the handyboard
|
|
(...) Yup. I have one of those tapeless tape measures with the smaller transducer, and the handyboard connected one is louder, so I wonder if that might be something? (30 years ago, 20-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: New motor drivers
|
|
(...) I am running 12 volt motors that draw about 1 amp each. They were the only motors that I had available for the project so I made due. Keith Keith Soldavin kas219@email.psu.edu (URL) (30 years ago, 20-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: New motor drivers
|
|
(...) The motors are 12 volt 1 amp motors. I know that the piggyback method will give me the higher current but I am not that fond of that method. I would prefer to have one controller that has power to spare than a rigged system that will just (...) (30 years ago, 20-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | IR for bots
|
|
Hello everyone, My thinking (albeit limited), has been that simply driving an IR LED with ac (ie:40Khz) as opposed to static dc, is enough to discriminate it from other frequencies like 60 Hz. or whatever. Then, when the detector picks up sufficient (...) (30 years ago, 20-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Sonar and the handyboard
|
|
(...) Since 8" is the 'minimum' distance the board can see, I strongly suspect that your transducer isn't sufficiently damped. This will cause it to continue 'ringing' after the pulse is sent and when the receiver switches on, its still vibrating so (...) (30 years ago, 20-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Sonar and the handyboard
|
|
(...) The one that is mounted is in a plastic box, glued in with silicon glue. The unmounted one was laying on my bench pointed at the ceiling. (...) I assume the 'blank inhibit' pin is BINH (docs are at home, I am at work), and that is connected to (...) (30 years ago, 20-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Sonar and the handyboard
|
|
mine is doing the same thing only it displays 7" i hear ticking constantly HELP bryan wiabel offrds2@aol.com (30 years ago, 20-Mar-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: New motor drivers
|
|
Yes. I use 12 V motors with these chips. The 1A ones. ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the Advancement of Science (...) (30 years ago, 20-Mar-97, to lugnet.robotics.handyboard)
|