To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1706 (+10)
  re: ztx614
 
(...) I think it must better be a darlinghton and it must support enough current: if you want to get 0.1A or more pulsed current in the IR led, the transistor must have a rather high current gain, more than that of an ordinary npn trans (by the way (...) (30 years ago, 19-Mar-97, to lugnet.robotics.handyboard)
 
  re: ztx614
 
(...) How are you gonna get 100 ma through a 1k resistor biased by 5volts?? The max would be 5ma. I have *never* heard of a LED this size that can handle more than 20ma!! This LED is tiny. I don't know where pin one of the jumper goes to or its use (...) (30 years ago, 19-Mar-97, to lugnet.robotics.handyboard)
 
  LCD compatible
 
Does anyone have experience using a Truly MCC162A1-2 16x2 LCD? I bought one from Wirz electronics for the handyboard. In assembly step 6.something, it says to power it up and there should be *faint* segments lit, if they are dark check pin1 to (...) (30 years ago, 19-Mar-97, to lugnet.robotics.handyboard)
 
  re: ztx614
 
On Wed, 19 Mar 1997, Stefano Nardone wrote (...) Thanks! that was not clear, where did you find info on j7? Is there a IR transmitter in the parts list? I didn't see one? Do you know what to use for a transmitter? thanks, jm (30 years ago, 19-Mar-97, to lugnet.robotics.handyboard)
 
  re: ztx614
 
(...) I just looked back to the IR transmitter schematic... The 1K res + RED LED you see there is for the only purpose of having a visible feedback of IR transmission. The IR Led and it's limiting resistor (if the case) will be connected in series (...) (30 years ago, 19-Mar-97, to lugnet.robotics.handyboard)
 
  Re: system time
 
please get me off this mailing list (30 years ago, 19-Mar-97, to lugnet.robotics.handyboard)
 
  Hall Sensor
 
Hi, Does anyone have recent model #'s, part #'s, or suppliers for Hall Effect magnetic sensors that interface directly with the Handy Board. There is a picture of a Hall sensor on page 52 of the Handy Board Technical Reference, but no part number or (...) (30 years ago, 19-Mar-97, to lugnet.robotics.handyboard)
 
  Re: Motorola Microprocessor source
 
(...) Most Connor disk drives have a 68HC11A1FN on them. If you find someone throwing one away, it is a cheap HC11. (...) Digi-key sells these. (...) Ben Wirz sells these. Also look for the TI replacement possibly. (30 years ago, 19-Mar-97, to lugnet.robotics.handyboard)
 
  Motorola Microprocessor source
 
Does anyone have a source for the following parts or suitable substitutes: Motorola 6811 microprocessor Hitachi 16x2 LCD Sharp IS1U60 infrared demodulator SGS-Thompson L293D motor driver William F. Conroy III conroyw@acm.org Lt Col, USAF (30 years ago, 19-Mar-97, to lugnet.robotics.handyboard)
 
  New motor drivers
 
Does anyone know an easy way to replace the motor drivers on the handyboard with the 18200 chip from National Semiconductor? The motors I am going to be driving need more current that the old ones can put out so I need to upgrade. I know that they (...) (30 years ago, 20-Mar-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR