To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1586 (+10)
  Re: IR Collision avoidance
 
At any point are you making an effort to detect your 40kHz IR signal? If you use the sharp IR detector to receive your 40kHz signal you are going to get an initial burst when the thing first turns on and then it will average out to zero just like (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
 
  Re: IR Collision avoidance
 
(...) The Sharp IR modules are not being used to detect distance, they are being used simply as non-contact bumpers. This allows one to inexpensively put an arbitrarily long 'whisker' on your robot. The advantage to these things are that they are (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
 
  Re: IR Collision avoidance
 
Actually, I built the (...) This is exactly the same scheme I use. I'm using an IR module from Digi-key that has a side view, and five IR LED's spread around the front of the module at different angles. I have quite a few outputs, thanks to a little (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
 
  serial comm
 
Good morning, I am building a handy board for the first time using the Douglas Electronics boards and parts from various sources. I have been following the assembly instructions to the letter but am now stuck at the end of section 4.4, Serial Line (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
 
  IR xmitter/receiver idea.
 
Heres a IR xmitter/receiver idea for you; I've seen this approach used in equipment and it works very well, I'm not sure how well it will work for robotics but believe it can be adapted. This is difficult to explain but easy to build, so hang with (...) (30 years ago, 3-Mar-97, to lugnet.robotics.handyboard)
 
  Re: IR Collision avoidance
 
The part number on the device from Radio Shack is "GP1U52X". In our earlier discussions, I thought I made it clear that I was using "the Radio Shack IR detector module", although I may not have quoted the number. If Sharp makes a module without the (...) (30 years ago, 4-Mar-97, to lugnet.robotics.handyboard)
 
  Re[4]: IR Collision avoidance
 
Adam, I don't use -5v, I just use a single 5v supply. You have to choose your op-amp carefully - I am currently trying ICL7612 but I'm looking at another sort which might turn out to be better. With a single supply, you have to bias things around (...) (30 years ago, 4-Mar-97, to lugnet.robotics.handyboard)
 
  Re[2]: phone cord length
 
TTL does NOT go down that line, it is RS232 which is commonly used at up to 50 feet. However, you might need to use a shielded cable if you use a lead longer than about 10 feet. Richard (30 years ago, 4-Mar-97, to lugnet.robotics.handyboard)
 
  Re: Re[2]: phone cord length
 
(...) On the phone cord between the handy board and the charger/interface card, the signal voltage is TTL levels. There is also charge voltage, and ground in the other wires. RS232 level conversion is done by the MAX232 on this card. (30 years ago, 4-Mar-97, to lugnet.robotics.handyboard)
 
  Re: Re[2]: phone cord length
 
(...) No, the MAX232 chip on the charger board converts from 12V RS232 coming out of the serial port to TTL level RS232. What goes down the line to the Handyboard is 5V RS232, which goes straight into the HC11 and at only 5V levels is more (...) (30 years ago, 4-Mar-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR