To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1446 (+10)
  (no subject)
 
Kent, I've been reading the documentation pertaining to the hookup of the Polaroid 6500 sonar and am a little bit unsure about some of the wording. Can you please verify with me a few things.... When you discuss the connections to the HB, it is (...) (30 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
 
  Sonar Query
 
Anyone, I've been reading the documentation pertaining to the hookup of the Polaroid 6500 sonar and am a little bit unsure about some of the wording. Can you please verify with me a few things.... When you discuss the connections to the HB, it is (...) (30 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Signal Diode
 
the 1n4001 is a pwr diode, not a signal, try looking in pwr section. -f In your message you said: (...) (30 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Signal Diode
 
The 1N4001 is the 50v version of a family of diodes (1N4001-1N4007) that cover 50 volts to 1000 volts. In general you could use any of the other versions. I would recommend looking for 1N4002(100v) or 1N4003(200v). As it happens Digikey says they (...) (30 years ago, 11-Feb-97, to lugnet.robotics.handyboard)
 
  sonar&motor driver
 
Hello everyone, If the polaroid sonar sensors are connected as mentioned by kent (ftp site), is it still possible to use motor ports 2 & 3? (30 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
 
  as11_ic
 
Hi, I was wondering if there is a version of the as11_ic assembler available for the IBM PC. If not, is there any other way to use an .asm file on the handy board? Thanks. -LUKE (30 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
 
  Re: Signal Diode
 
JTW, Use 1n4002, 1n4004, etc - they are higher rated parts and usually the same price (which is why 1n4001 has been discontinued - everybody upgraded for free!). Richard ___...___ Reply Separator ___...___ Subject: Signal Diode Author: (...) (30 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
 
  Building new PCODE
 
As I cant seem to get a 16x2 LCD, I have installed a 16x1 display. The problem now is building a suitable version of the PCODE to support it without workarounds. I don't have a unix box so I got Kent's (?) port to the PC. That, however, is an older (...) (30 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
 
  as11_ic
 
Hi, I was wondering if there is a version of the as11_ic assembler available for the IBM PC. If not, is there any other way to use an .asm file on the handy board? Thanks. -LUKE (30 years ago, 12-Feb-97, to lugnet.robotics.handyboard)
 
  Re: as11_ic
 
There are two fundamentally different ways to go about writing assembly language programs for the Handy Board: 1. Write them as callable functions for the Interactive C environment, using the as11_ic program. 2. Scrap Interactive C entirely, and (...) (30 years ago, 12-Feb-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR