 | | Weak Motor
|
|
I have try to run the handy board using the standard DC 9V motor purchase from one of the vendors. However , it does not seem be able to move very well though i put it to 100% of its capacity. I am now working on a project to built a remote car (...) (27 years ago, 24-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: something is wrong with my handyboard
|
|
Chau, sounds like either (a) your LCD screen went bad, or (b) there is a bad connection betw the LCD screen and the rest of the HB. fred In your message you said: (...) (27 years ago, 24-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Homing with the IR Tower
|
|
(...) So far I have been using the tachometers mainly to find the mid-point of the signal band, so they don't have to be too accurate. The need of accuracy will arise when I use them for soda can detection. Let's see. I have posted my current design (...) (27 years ago, 24-Jul-99, to lugnet.robotics)
|
| |
 | | Re: HB Serial line speed change
|
|
(...) The definitive answer comes from the "pink" book, which everyone should have (especially now that you can get it on CD-rom for free by filling out the form on the Mot web site!) Which basically says "No you can't do that." But it says it in a (...) (27 years ago, 24-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | RCX IRPD kits are now gone
|
|
Hi all, again, Those 8 RCX IRPD kits are now all spoken for. Thanks for helping clean up my shop 8^) of these last unclaimed kits. have fun, DLC (27 years ago, 25-Jul-99, to lugnet.robotics)
|
| |
 | | Re: HB Serial line speed change
|
|
(...) You can communicate at higher baud rates (19200 or 38400) on an 8MHz 68HC11 if you disable SCI and use software "bit-bashing" routines. I have enclosed examples of such routines in sw_baud.s11 file. Setting the BIT_TIME to 52 or 104 allows you (...) (27 years ago, 25-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: HB Serial line speed change
|
|
(...) Note that this will also require that you disable interrupts, and that will mess up your motors. However, it should be possible. --Chuck (27 years ago, 25-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: LEGO data drive
|
|
(...) Check out (URL) is in Japanese, but the idea is definitely still there. -Luis (27 years ago, 25-Jul-99, to lugnet.robotics)
|
| |
 | | RE: CyberMaster tracks (was Re: LEGO Lawn-mover)
|
|
Anyone been able to get hold of the cybermaster tracks on their own ! from Dacta ? maybe David Walton Email: d.walton@ndirect.co.uk Take a look at my homepage (still under construction though) (URL) on ICQ: 44277445 "If it ain't broke don't fix it (...) (27 years ago, 25-Jul-99, to lugnet.robotics)
|
| |
 | | Re: something is wrong with my handyboard
|
|
I had a similar problem. In my case, the cause was underneath the board. I had not trimmed one of the components leads enough. When I screwing the board into the case the lead eventually pierced one of the wires going to my Nicad pac. My board would (...) (27 years ago, 25-Jul-99, to lugnet.robotics.handyboard)
|