To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *12836 (+10)
  Re: Yet another board
 
Chuck, nice dream! I would be in too. But why not design a kind of a extension board which would replace the curend extension board? It would save some money i guess. Thomas. (...) (27 years ago, 23-Jul-99, to lugnet.robotics.handyboard)
 
  RCX IRPD kits left
 
If there is anyone out there that expressed interest in the RCX IRPD kits that you convinced me to assemble parts for, let me know. I still have 8 kits left, I'd hate to have them (and their parts!) go to waste. So, if you sent me email with (...) (27 years ago, 23-Jul-99, to lugnet.robotics)
 
  Re: Homing with the IR Tower
 
(...) I'm glad to hear that I'm not the only person who's still trying to solve Joel's challenge. It sounds like you've made some great progress! (...) Congratulations! Another Lego Fan is born! (...) Same here! <snip!> (...) I had considered (...) (27 years ago, 23-Jul-99, to lugnet.robotics)
 
  Re: something is wrong with my handyboard
 
it sounds like the pcode is going down onto the board, but you may have an open on your lcd header / connector. if you can talk to the board using ic (make it beep or such) then it's just the lcd output. check for open circuits first. (...) (27 years ago, 24-Jul-99, to lugnet.robotics.handyboard)
 
  Re: HB Serial line speed change
 
Here is the relevant function. Note that it only works for baud rates up to 9600. void set_baud(int rate) /* For an 8 MHz clock */ { if (rate >= 300) poke(BAUD, 0xb0 | log2(9600/rate)); } You'll need regdefines.c (for the address of BAUD) as well as (...) (27 years ago, 24-Jul-99, to lugnet.robotics.handyboard)
 
  Weak Motor
 
I have try to run the handy board using the standard DC 9V motor purchase from one of the vendors. However , it does not seem be able to move very well though i put it to 100% of its capacity. I am now working on a project to built a remote car (...) (27 years ago, 24-Jul-99, to lugnet.robotics.handyboard)
 
  Re: something is wrong with my handyboard
 
Chau, sounds like either (a) your LCD screen went bad, or (b) there is a bad connection betw the LCD screen and the rest of the HB. fred In your message you said: (...) (27 years ago, 24-Jul-99, to lugnet.robotics.handyboard)
 
  Re: Homing with the IR Tower
 
(...) So far I have been using the tachometers mainly to find the mid-point of the signal band, so they don't have to be too accurate. The need of accuracy will arise when I use them for soda can detection. Let's see. I have posted my current design (...) (27 years ago, 24-Jul-99, to lugnet.robotics)
 
  Re: HB Serial line speed change
 
(...) The definitive answer comes from the "pink" book, which everyone should have (especially now that you can get it on CD-rom for free by filling out the form on the Mot web site!) Which basically says "No you can't do that." But it says it in a (...) (27 years ago, 24-Jul-99, to lugnet.robotics.handyboard)
 
  RCX IRPD kits are now gone
 
Hi all, again, Those 8 RCX IRPD kits are now all spoken for. Thanks for helping clean up my shop 8^) of these last unclaimed kits. have fun, DLC (27 years ago, 25-Jul-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR