 | | Re: Cannot Find pcoder22.s19
|
|
(...) I think everybody had that problem at first, because the default setup for IC tries to use that file. The pcoder22.s19 is not supposed to be used for the HandyBoard (I think it's for the MIT robotics course). Your HB needs the pcode_hb.s19 (...) (27 years ago, 6-Jul-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
oops. forgot to divide by 2. make that between 600 and 720 RPM. I called pitsco lego dacta and they report 350 RPM... i wonder if i'm doing something else wrong in my analysis... but i can't find it! anyone else? (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
I found only this post in a search of LUGNET Robotics for "RPM" (...) -- Did you check the web site first?: (URL) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
thanks. i found out that my time axis on my graph had numbers about half of what they should have been, so I got around 350 RPM too. yay. -Ben (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | more fun with cross-compilers
|
|
I posted here quite some time about this, and got a single personal response which has now been lost into the bowels of my pine folder "system." (hah!) Has anyone successfully set up a cross compiler on solaris 2.7? While building the binutils, I (...) (27 years ago, 6-Jul-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: *** NQC ***
|
|
NQC is actually two things: a language to program the RCX and a compiler for that language. (at first I distinguished between the language: NQC, and the compiler: nqcc, but this was even more confusing) RcxCC is a great front-end for NQC. It (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
Keep checking the math. I clocked the motor at 330 - 350 rpm. I used the rotation sensor driven directly by the motor. From analysis of the RCX firmware, the rotation sensor should be accurate to 1250 rpm, so I'm pretty confident of it being in the (...) (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Virtual PC and Mindstorms
|
|
Robolab uses the same RCX as Mindstorms - I have one of each and they are identical (short of the number stamped on the side). Dave (...) reply to: dbaum at enteract dot com (27 years ago, 6-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
(...) Dave- Where are you getting that 1250 rpm upper limit from? While I haven't counted exactly yet, I'm dropping only 20 counts out of every thousand at ~15,000 rpm. I had assumed this was mainly gear slop, since it only appears to occur while (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|
| |
 | | Re: What is RPM of Gear Motor???
|
|
Using a Futaba 9ZAP radio with a built in optical tachometer and the two bladed LEGO prop I got 380 rpm for the gearhead motor and 4320 rpm for the older nongeared motor. Of course this was done with a battery box and brand new batteries so I am (...) (27 years ago, 7-Jul-99, to lugnet.robotics)
|