To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *12296 (+10)
  Re: NQC tuturial
 
(...) Start at the official NQC site: (URL) are a few sample programs there. There's also a link on the "Information" page to Mark Overmar's site which contains an excellent tutorial. Dave (27 years ago, 26-Jun-99, to lugnet.robotics)
 
  Re: signals / legOS internals
 
(...) No, you should not abandon your implementation - not if you want to use LegOS. I was only explaining how I implemented similar functionality, for the sake of comparison. Regarding Librcx, I might release another version at some point, to add (...) (27 years ago, 26-Jun-99, to lugnet.robotics.rcx.legos)
 
  Re: NQC tuturial
 
(...) All of the bots on my pages include NQC source. URL in the sig below. Play well! - Ben. ---...--- Ben Williamson benw@pobox.com (URL) you check the web site first?: (URL) (27 years ago, 26-Jun-99, to lugnet.robotics)
 
  building handyboard
 
I am building a handyboard and wnat to know if a 470mf capacitor with 16v is ok to use for the board. ___...___ Do You Yahoo!? Get your free @yahoo.com address at (URL) (27 years ago, 26-Jun-99, to lugnet.robotics.handyboard)
 
  LM35 Temp Sensor
 
Hi, Has someone tried to connect a LM35 temperature sensor to an analog input in the HB, I have had no luck with it, I have plugged it directly to the input and think that maybe is the 47K pull-up resistor the cause of the problem. Thank You José (...) (27 years ago, 26-Jun-99, to lugnet.robotics.handyboard)
 
  Re: legOS make newbe question
 
(...) More to the point, it cannot recognize the '(cd' command. Now, why that is, or how you can fix it, I do not know. It would appear to be a problem with make or with your shell. It should just be farming the entire line off to the shell, which (...) (27 years ago, 26-Jun-99, to lugnet.robotics.rcx.legos)
 
  Re: signals / legOS internals
 
(...) Cool. I will proceed. (...) Yup. I was out of the loop for awhile, and am once again whompin' on this project. (...) That is true. Signals would give the task the opportunity to stop/start tasks under its control, though, without the task that (...) (27 years ago, 26-Jun-99, to lugnet.robotics.rcx.legos)
 
  Re: legOS make newbe question
 
Thanks Lou, I am sure that you are right. I also don't know what could cause it or how to fix it. I just hope there is some bright person who reads this NG and can get me on to the next step. Based upon the discussion topics that I have seen, this (...) (27 years ago, 26-Jun-99, to lugnet.robotics.rcx.legos)
 
  Re: IC question
 
Dear Victor, I'll give you a few hints about what you are trying to do. 1. the "0x" in front of 0x0e is the same as "$" in regular C. It just designates that the number following is in hex format. 2. Fred runs his motor driver chips using addresses (...) (27 years ago, 26-Jun-99, to lugnet.robotics.handyboard)
 
  Re: legOS make newbe question
 
(...) Some versions of make look for the sh shell, others use the dos shell. Probably, make is using the dos shell and not sh. As far as I know, make does not parse the parens, the shell does. And dos does not understand the parens. My cygwin make (...) (27 years ago, 26-Jun-99, to lugnet.robotics.rcx.legos)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR