To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *11771 (+10)
  Sony Robotic Dog: Check it Out!
 
(URL) dog is wild! It can learn behaviors and it can be reprogrammed! Ross M. Tonkens, M.D. Medical Director Primary Care of Nevada 100 North Green Valley Parkway Suite 240 Henderson, NV 89014 702 914-7120 VOICE 702 914-7129 FAX (27 years ago, 23-May-99, to lugnet.robotics.handyboard)
 
  Sony Robotic Dog URL correction
 
I misquoted the URL. Typed so fast, I left out the world wide web prefix. It should read: (URL) Tonkens (27 years ago, 23-May-99, to lugnet.robotics.handyboard)
 
  Re: Using SPI
 
(...) Gary, We used the PA7(transmitting board) and PD0(receiving board) in wireless and wired mode. This is quite easy to do. Pete Eacmen have done the wired stuff while I did the wireless stuff. With wired one, you can transmit @9600 baud with no (...) (27 years ago, 23-May-99, to lugnet.robotics.handyboard)
 
  Not lego, but interesting...
 
Good job for Sony engineers (URL) José Antonio Vacas Martínez (...) -- Did you check the web site first?: (URL) (27 years ago, 19-May-99, to lugnet.robotics)
 
  Windows CE
 
does anyone know of a way to program the RCX from a CE device? -- Did you check the web site first?: (URL) (27 years ago, 20-May-99, to lugnet.robotics)
 
  Problems with Macintosh and Robolab
 
---...--- Problems with RCX and ROBOLAB for Macintosh ---...--- I can't get any communication from Macintosh to RCX. The RCX and the IR-tower are okay - the connection from a Windows98-PC to RCX shows no errors. Trying any port (modem or printer) I (...) (27 years ago, 21-May-99, to lugnet.robotics)
 
  Sony Robotic Dog: Check it Out!
 
(URL) it out. The robot learns from experience. It can also be programmed to exhibit new behaviors. Ross M. Tonkens, M.D. Medical Director Primary Care of Nevada 100 North Green Valley Parkway Suite 240 Henderson, NV 89014 702 914-7120 VOICE 702 (...) (27 years ago, 23-May-99, to lugnet.robotics)
 
  Re: Windows CE
 
I think the best way would be to port NQC, Dave Baum makes the source freely available. (...) -- Did you check the web site first?: (URL) (27 years ago, 24-May-99, to lugnet.robotics)
 
  Re: Problems with Macintosh and Robolab
 
I don't think speed is a problem. I was running an early version of Robolab on a 604e/132MHz. It was annoyingly slow to use, but it was able to talk with the RCX. You may want to try the IR tower in both "near" and "far" modes (that's the switch on (...) (27 years ago, 24-May-99, to lugnet.robotics)
 
  Fwd: Re: Problems with Macintosh and Robolab
 
Hallo Dan, yes, I have already updated the serial drivers - without any result. NQC connects fine but not ROBOLAB. I wanted to try iconic programming with ROBOLAB. Ralf (...) to (...) robolab (...) try (...) --- Sent through Global Message Exchange (...) (27 years ago, 24-May-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR