 | | Re: Sharp 2L01
|
|
Scott Sherman wrote: <snip> (...) Scott: The Hamamatsu P5587 photoreflector is great for use as a shaft encoder. It's available from Zagros Robotics at: (URL) - - - Nick - - - (28 years ago, 10-May-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: SHARP new product
|
|
Steve Richards of Acroname says he will be carrying both the GP02D12 and GP02D15 within the next few weeks...<smack!> -Drew -----Original Message----- From: Bill Denzel [mailto:wdenzel@poly...lpoly.edu] Sent: Monday, May 10, 1999 2:35 PM To: (...) (28 years ago, 10-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Some goals, ideas, etc. for a new bytecode interpreter (long)
|
|
(...) While I agree that it should be similar, I think it may need some minor modifications to make it truly useful. For example, I would like to be able to control the motors without having to load a program or use a host computer. It would be nice (...) (28 years ago, 10-May-99, to lugnet.robotics.rcx)
|
| |
 | | Battery question
|
|
Hello all, I currently have a 12v 2amp camcorder gel-cell as a motor power source for some 12-24v gearhead motors purchased from Acroname. I am using stacked L239's and TI motor driver chips to interface. All is working, except that the motors only (...) (28 years ago, 10-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Some goals, ideas, etc. for a new bytecode interpreter (long)
|
|
(...) I was not intending to limit its functionality to that performed by the RCX with the standard firmware loaded. I did say "when no new features are being exploited". The idea of flashing an identifier associated with the current program may not (...) (28 years ago, 10-May-99, to lugnet.robotics.rcx)
|
| |
 | | Re: Some goals, ideas, etc. for a new bytecode interpreter (long)
|
|
(...) Sure, but that's what zero padding is for. Since the opcode is IR-only, you don't care too much about length. The only length restriction comes from the second digit of the opcode, assuming you're using the ROM to receive incoming IR data. (...) (28 years ago, 10-May-99, to lugnet.robotics.rcx)
|
| |
 | | .rcx alternative firmware group/list
|
|
(...) John and several other people are set up with the new group and successfully posting to it, so this info is for anyone else: lugnet.robotics.rcx is a newsgroup running on the lugnet.com newsserver and it is available via e-mail as (...) (28 years ago, 10-May-99, to lugnet.robotics, lugnet.admin.general)
|
| |
 | | Re: Some goals, ideas, etc. for a new bytecode interpreter (long)
|
|
(...) You have 4 7-segment characters which could display a 4 character text string (albeit with some of the characters being different case and some confusion between characters). (...) Adding limited functions to check the memory usage without (...) (28 years ago, 10-May-99, to lugnet.robotics.rcx)
|
| |
 | | Re: Some goals, ideas, etc. for a new bytecode interpreter (long)
|
|
(...) Single-stepping through instructions would be a mode offered by the interpreter, and wouldn't require any breakpoints to be set. I suppose what the debugging information could contain is, instead of a list of valid breakpoints, a list of (...) (28 years ago, 10-May-99, to lugnet.robotics.rcx)
|
| |
 | | **wall wart for RCX**
|
|
Hi all, I was wondering what is the voltage and amps req. for the rcx and what about ac dc polarity? Any help would be very much appreciated. Thanks! -Mike -- Did you check the web site first?: (URL) (28 years ago, 10-May-99, to lugnet.robotics)
|