 | | Batteries
|
|
Hi Guys, I was wondering if is it safe to use a 9.6V battery pack with a current rating of 1A or more? (28 years ago, 9-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Some comments (long)
|
|
(...) Hmmm... I guess I have to explain every little word I write so as not to get flamed. People fear Java on a small memory platform because when they run a JVM for any length of time on their Wintel boxes they see it slowly "gobble" more and more (...) (28 years ago, 9-May-99, to lugnet.robotics)
|
| |
 | | charger
|
|
I have an old 'wall wart' lying around. It has a rating of (12 vdc 1 amp output). i was wondering if i can use it on the handy board. the specs i read about the handy board call for a 12v 500mAmp output. any response would be appreciated. FRED (28 years ago, 9-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Would-be hacker queries. / Re: Request for new list
|
|
Valid questions, all of them. We do tend to remain in the upper ranks of CS on this list. I'll see if I can take a stab at defining some terms quickly and clearly. BTW, I wouldn't mind adding my knowledge of CS to a FAQ for newbies. Mindstorms will (...) (28 years ago, 9-May-99, to lugnet.robotics)
|
| |
 | | Re: Batteries
|
|
(...) Umm, not sure what you mean by "a current rating of 1A or more". Do you mean 1Ah ? It's certainly alright to use a 9.6v battery with a *capacity* of 1Ah or more... Cheers, Duncan (28 years ago, 9-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: charger
|
|
(...) In short, No. The charging cicuitry on the HB (especially the zap mode) is designed for a 500ma supply. People have had problems with 1 amp ones. Best, Duncan (28 years ago, 9-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Would-be hacker queries. / Re: Request for new list
|
|
Hi again. Laurentino was so kind as to give me the definitions of the terms I mentioned. Is it generally agreed that an intelligent newby can ask for definitions of technical terms, as the discussion goes along? If so, I'll try to keep it (...) (28 years ago, 9-May-99, to lugnet.robotics)
|
| |
 | | Re: Would-be hacker queries. / Re: Request for new list
|
|
Great, Eric! Great answers. Thanks for your help. In cooperation, I think we can compile an awesome programming FAQ. The robots are coming! I'm very excited by the future of robotics in the wake of developments including the RCX. I get the (...) (28 years ago, 10-May-99, to lugnet.robotics)
|
| |
 | | SHARP new product
|
|
Hello everyone, Sharp recently release the new GP2D12 (General Purpose Distance Measuring Sensors). Which performs same as the GP2D02. The new product have only 3 pins - Vo, Gnd, and 5V. Vo is an analog output, which means you can use it on any (...) (28 years ago, 9-May-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: charger
|
|
(...) I'm relying on non-handyboard experience here, but I'm going to assume that's too much. One amp is a heavy load, and although there's a 5v regulator on the circuit, I'd guess that it's not rated for 1 amp (it may just run hot) and might not be (...) (28 years ago, 10-May-99, to lugnet.robotics.handyboard)
|