 | | Re: Replacing Motor Driver 754410's
|
|
(...) I concur here, I have a 6inch X 6inch piece of aluminium for 2 of them, and this seems to dissapate all the heat I am generating. I could see longer runs or steeper grades would require a larger heatsink. (...) I was the one who originally (...) (30 years ago, 13-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | 10 or 12 bit A/D?
|
|
Hello, I am interested in a 10 or 12 bit A/D version of the Handy Board. Does anyone have any information that might assist me? Thanks in advanced. ...Bye, Kevin Hollander Kevin Hollander Univ. of New Mexico Dept. of Mechanical Engineering (...) (30 years ago, 13-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Handy Board supplier ?
|
|
I am new on this list and I wander if anybody can help me with information about a supplier of 'Handy Board' with a reasonable price; the ~$280 it's excessively high for me. Thanks Gyuri (30 years ago, 13-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Polaroid Sensors
|
|
Hey Everybody, Quick question for you. Just bought two Polaroid ultrasonic ranging modules, and I would like to know if I must use the Propulse batteries and holder that the manual suggests. If not, does anyone have any suggestions for a substitute (...) (30 years ago, 13-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polaroid Sensors
|
|
The HB power source will work. Plug the power lines into the +5v and GND anywhere on the HB's headers. (...) (30 years ago, 14-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Sonar and encoder conflict.
|
|
I am attempting to run the following routine on my Handyboard int check() { int inches; ping(0); msleep(35L); inches=sonar_time/150; printf("%d \n",inches); return inches; } The program runs great and returns the proper value (Thanks to the software (...) (30 years ago, 15-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | steppers - HB
|
|
Wondering if anyone knows of a good way to interface a couple of steppers to the HB AND if there are any ic routines written to control steppers. Ideas, comments, suggestions, questions welcome. Bruce (30 years ago, 16-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Good Times virus warning!
|
|
Sorry, I can't help myself. I have a 102 deg fever right now and I am not thinking straight. -Fred ------- Forwarded Message <<Subject: Final warning about the "Good Times" virus>> READ THIS: Goodtimes will re-write your hard drive. Not only that, (...) (30 years ago, 16-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Handy board parts
|
|
I am searching for HB parts such as the 32K static CMOS ram p/n 62256-100LP, voltage monitor, p/n DS1233-10, IR demodulator p/n IS1U60, motor driver p/n L293, RS232 converter p/n MAX232CPE, or any acceptable substitutes. Would appreciate anyone (...) (30 years ago, 17-Dec-96, to lugnet.robotics.handyboard)
|
| |
 | | Getting started
|
|
Hello to all, I am a senior in High school and I would like to get into robotics. I bought "Mobile Robtics" and have read parts of it. Is the Handy Board a good place to start? I would really like to get into some AI later. Does anyone have any (...) (30 years ago, 17-Dec-96, to lugnet.robotics.handyboard)
|