To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10711 (+10)
  Re: Smooth PWM for IC3.2?
 
(...) This problem is the only reason why I'm not buying the commercial version of IC. I'd buy in an heartbeat if *all* the code running on the handy board was available. Until then I stick with the free version. So far I've modified my pcode at (...) (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Steering a robot
 
(...) I have two designs that use separate steering and propulsion motors: (URL) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Re: **lego motors?**
 
Use the "differtrans." See (URL) OR AT (URL) M. Tonkens, M.D. Medical Director Primary Care of Nevada 100 North Green Valley Parkway Suite 240 Henderson, NV 89014 702 914-7120 VOICE 702 914-7129 FAX BMajik5127@aol.com (...) RMT -- Did you check the (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Desgning H-bridge
 
Where can we get info in designing H-bridges from descreet components? Is it sufficient to use just four MOSFETs or just four solid state relays? Thanks for any input. ---...--- ericson mar Robotics Consultant mar@cooper.edu (212)353-4356 Department (...) (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Steering a robot
 
Thanks to everyone that responded. I do indeed have a differential setup on the rear wheels and a second differential to incorporate the power of two motors. The steering problem is that I don't know how to reset the steering wheels on the front of (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Re: Desgning H-bridge
 
Hey Ericson, Check out the following sites for motor control information: (URL) under motor control Hope this helps, good luck! --kam (URL) Mon, 12 Apr 1999, MAR ERICSON wrote: -->Where can we get info in designing H-bridges from descreet (...) (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Rangingproblems with Sharp GP2D02
 
Hi all I just finished rewriting the GP2D02 routines by Kent. Seems all to work just fine....except that I don't get readings below around 55. Even if I don't have anything in front of the sensor (dist. to wall more than 2m) I never get a reading of (...) (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Desgning H-bridge
 
Another great source for h-bridge design if (URL) It gives details on how to build a PIC based motor controller, but more importantly, it has a great h-bridge schematic. Be sure to check it out. ---...--- Brian Schimpf schimpfy2@aol.com (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Rangingproblems with Sharp GP2D02
 
(...) I'm looking at the Sharp data sheet, and they have a chart that shows decimal distance measuring output vs distance to object in centimeters, and they indicate the minimum reading to be around decimal 59 to 64 depending on object reflectivity. (...) (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Expansion Board Servo timing...
 
Drew- I have a Handy Board on a robot that runs three servos and the GP2D02 sensor, and I have the same nervous jitters problem. However, I do not run any processes on this application. I am using IC under v 3.2 of the software, so I could use (...) (28 years ago, 12-Apr-99, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR