 | | Re: Which glue?
|
|
(...) I still swear by Goop. But I have to ask what the hec is this for? (URL) (17 years ago, 22-Feb-08, to lugnet.parts.mod)
|
| |
| | Re: How do -you- clean your LEGO parts?
|
|
(...) I use washing machine. I pre-sort the parts, plates longer than 8 go out, anything printed/glass/sticke...d/electric goes out, and also the things from softer plastic should go (trees, clips etc.). Then I put it in cloth bag (old pillow), (...) (17 years ago, 21-Feb-08, to lugnet.parts)
|
| |
| | Re: How do -you- clean your LEGO parts?
|
|
(...) Tooth brush is what I use to be very careful, and an old electric tooth brush. For large amounts I use the dish washer on delicate, cold water, bricks in a girly stuff bag, no drying. I take them out and put them under a fan after laying them (...) (17 years ago, 21-Feb-08, to lugnet.parts)
|
| |
| | Re: Which glue?
|
|
(...) Brian, I would try a dab of silicone adhesive caulk. You can check the specs but think would be good down to -60----if not there are some that are. Messy but would bet it would work. Also, try roughing up the beam with bit of sandpaper which (...) (17 years ago, 21-Feb-08, to lugnet.parts.mod)
|
| |
| | How do -you- clean your LEGO parts?
|
|
I don't think LUGNET has had any discussions about this in quite some time. How do -you- clean your LEGO parts? I'm interested in learning people's techniques, particularly ones that clean a lot of parts at once with little effort. LEGO that's been (...) (17 years ago, 21-Feb-08, to lugnet.general, lugnet.parts)
|
| |
| | Re: Which glue?
|
|
(...) Brian, Have you tried Gorilla Glue? You just have to be careful not to use too much as it expands as it dries. I'm also assuming that it's the flat-plain side(s) of the beam (not the technic pin hole side(s) ) that you are trying to affix to (...) (17 years ago, 21-Feb-08, to lugnet.parts.mod)
|
| |
| | Re: Which glue?
|
|
(...) OK, to revive this thread, I've had zero luck gluing ABS studless beams to the backside of mirrors - superglue doesn't seem to stick at all. Any ideas? What am I doing wrong, etc.? 2 component epoxy isn't likely to work either, given the (...) (17 years ago, 21-Feb-08, to lugnet.parts.mod)
|
| |
| | Re: Can't find this part on Peeron: 2x2 plates with connecting stem
|
|
(...) That's more or less correct. If you pull up an individual part entry, the far right column shows what sets it's been used in (if it's a part, minifig, or some other sub-component of a set), and the next column to the left will give you rolling (...) (17 years ago, 30-Jan-08, to lugnet.parts)
|
| |
| | Re: Can't find this part on Peeron: 2x2 plates with connecting stem
|
|
(...) Lugnet has a tab somewhere in the catalog section that gives the high and low and average price or medium price. It is very handy as I think that it keeps track of what was sold and does not reset once there are none on Bricklink John P (17 years ago, 29-Jan-08, to lugnet.parts)
|
| |
| | Re: Can't find this part on Peeron: 2x2 plates with connecting stem
|
|
(...) That is the inherent difficulty when selling such parts, there is no sound way to determine up ahead what a person would be willing to pay for it. Since I'm not in demant for it either, my "gut feeling" estimate for the price would be a low (...) (17 years ago, 29-Jan-08, to lugnet.parts)
|
