|
|
 | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) I've always found it interesting that 1x3 and 2x3 bricks and plates are the only odd length elements of those general categories. As you mention, there's no 1x5, no 2x5, no 1x7, no 2x9 and so on. I assume this is by design, but then you have (...) (20 years ago, 5-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: HELP needed with non-functioning 1x2 light brick!
|
| (...) Hi Samarth, I thought I read somewhere here on LUGNET that the lights are incandescent and will eventually give out. I'm not sure though. All hail hitechnic. e (20 years ago, 5-Feb-05, to lugnet.parts, lugnet.storage, lugnet.general)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| The piece I really want is 2x5 or 1x5 (or x7) bricks and plates. When building a MOC that's an odd number of studs wide, you have to either make it asymmetrical or use x1 and x3 bricks which aren't good for structural support. (20 years ago, 5-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) If you're going to explore these kinds of things, I recommend you learn how to create LDraw parts (or what's easier, editing existing ones). It's really not that hard. Also in many cases you can get a pretty good approximatin by just (...) (20 years ago, 5-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: HELP needed with non-functioning 1x2 light brick!
|
| (...) This may seem obvious, but if you're using a wire to connect it to a battery box, is it the wire? Does the battery box work properly? Does the battery itself work? Try checking out those parts too. -Bryan (20 years ago, 4-Feb-05, to lugnet.parts, lugnet.storage, lugnet.general)
| | | | | HELP needed with non-functioning 1x2 light brick!
|
| (Not sure exactly where this should go) I have an old (say about 7-8 years old) electric light and sound brick 1 x 2 with top lamp that has never given me trouble until now. I tried clearing the muck off the contacts, rearranging it in various ways, (...) (20 years ago, 4-Feb-05, to lugnet.parts, lugnet.storage, lugnet.general)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| Oops, sorry. Here are some deep links, to use until the folder is moderated... (...) (URL) (...) (URL) Steve (20 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) So, like one of these? (URL) Diagonal edge (URL) Round edge Steve (20 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) Are you doing 3rd angle projection or 3D? 10 minutes is a lot less than it took me in Paint. I suppose once you're trained in AutoCAD, a lot of things are quick. Could you post jpegs of the results? I created bits like studs in the drawing and (...) (20 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) Thanks, I like to do a proper job :-) (...) Up to now, there is no plate to go with the 4x4 round brick and the half cylinders. This means that unless your round bricks have exactly 4 bricks between them, you can't support them at the side (...) (20 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
|
|
