|
|
 | | Re: HELP needed with non-functioning 1x2 light brick!
|
| (...) Hi Samarth, I thought I read somewhere here on LUGNET that the lights are incandescent and will eventually give out. I'm not sure though. All hail hitechnic. e (21 years ago, 5-Feb-05, to lugnet.parts, lugnet.storage, lugnet.general)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| The piece I really want is 2x5 or 1x5 (or x7) bricks and plates. When building a MOC that's an odd number of studs wide, you have to either make it asymmetrical or use x1 and x3 bricks which aren't good for structural support. (21 years ago, 5-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) If you're going to explore these kinds of things, I recommend you learn how to create LDraw parts (or what's easier, editing existing ones). It's really not that hard. Also in many cases you can get a pretty good approximatin by just (...) (21 years ago, 5-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: HELP needed with non-functioning 1x2 light brick!
|
| (...) This may seem obvious, but if you're using a wire to connect it to a battery box, is it the wire? Does the battery box work properly? Does the battery itself work? Try checking out those parts too. -Bryan (21 years ago, 4-Feb-05, to lugnet.parts, lugnet.storage, lugnet.general)
| | | | | HELP needed with non-functioning 1x2 light brick!
|
| (Not sure exactly where this should go) I have an old (say about 7-8 years old) electric light and sound brick 1 x 2 with top lamp that has never given me trouble until now. I tried clearing the muck off the contacts, rearranging it in various ways, (...) (21 years ago, 4-Feb-05, to lugnet.parts, lugnet.storage, lugnet.general)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| Oops, sorry. Here are some deep links, to use until the folder is moderated... (...) (URL) (...) (URL) Steve (21 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) So, like one of these? (URL) Diagonal edge (URL) Round edge Steve (21 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) Are you doing 3rd angle projection or 3D? 10 minutes is a lot less than it took me in Paint. I suppose once you're trained in AutoCAD, a lot of things are quick. Could you post jpegs of the results? I created bits like studs in the drawing and (...) (21 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) Thanks, I like to do a proper job :-) (...) Up to now, there is no plate to go with the 4x4 round brick and the half cylinders. This means that unless your round bricks have exactly 4 bricks between them, you can't support them at the side (...) (21 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
| | | | | Re: New Parts Drawings - Plates, Slope, Track Pieces
|
| (...) OK, so the piece is like this: 1. The base is 3x3. 2. Is the corner a right angle, an 8mm radius curve, or a 16mm radius curve, like this piece? (URL) 3. I assume it has 2x2 studs on top, as if two 2x3s with curved top had been superimposed at (...) (21 years ago, 4-Feb-05, to lugnet.parts.custom, FTX)
|
|
