Subject:
|
Re: Best Way to Cut Baseplates
|
Newsgroups:
|
lugnet.general
|
Date:
|
Wed, 6 Mar 2002 11:33:24 GMT
|
Viewed:
|
1364 times
|
| |
|
|
In lugnet.general, Adrian Egli writes:
> I like both Lester's idea and yours. Getting cheapo non-Lego bricks is easy
> in my group and hacking those up sounds more pleasurable than the real
> stuff. It's been those inside corners that have really been in my head and
> the drill idea sounds like a good solution to that problem.
>
> One thing has come to mind, many of the cuts involved will be "long", so to
> speak, but narrow. (I just use a good sharp utility knife w/ blades I can
> replace, a good straight edge, clamps and PRAY.) The goal of the project is
> to form a curve (90 degree arc) using three 48x48 baseplates and use 1xn
> partitions to get the curve. It's been all drawn up on paper and the radii
> go from 64 studs inner to 80 studs outer giving me a bunch of 1xn's (longest
> appears to be 1x45) . Here's the Q, is there a clipper or some sort of
> scissor device I could use to nip that remaining 1 stud holding it? Would
> sure speed up things.
>
> Adr.
>
> "Bianca Nebab" <brgn@worldnet.att.net> wrote in message
> news:GsIvrr.FD@lugnet.com...
> > If you want to do this by hand and you are patient, you can make these • cuts
> > by using a small drill for the intersections of the cuts and a very sharp
> > blade such as an X-Acto. Drill first, then cut by repeated scoring between
> > the 2 drilled points (10-15 scores usually does it for me). I've used this
> > method to cut unusual patterns such as a 2nd level building floor with a
> > cutout around steps.
> > binky
> >
> > "Adrian Egli" <adr.egli@worldnet.att.net> wrote in message
> > news:GsIBLr.4Lu@lugnet.com...
> > > I'm in a design "pickle" of sorts. Not too long ago I began cutting up • the
> > > 48 studs sq. baseplates to retangular forms so I may use them on • platforms
> > > for bridges. OK, that's easy, but how can I do "stepped" cuts? Say, I • want
> > > to cut out an area, starting from the corner, of 2x8. Following that • would
> > > be a cut of 2x9 then 2x10 and so forth. By the time its over, holding • the
> > > baseplate up, you'll have a series of risers w/ a measure of 2 studs and
> > > landing w/ measures of 1 stud, "steps" if you will.
> > >
> > > Your knowledge is welcome.
> > >
> > > --
> > > Adrian Egli
> > > http://www.scltc.org
> > >
> > >
> >
> >
Clippers that would cut something as thick as a baseplate might have problems
with the studs getting in the way. I really think a scroll saw is the way to go
use a spiral bit which can change cutting directions at any time (0 turning
radius). I would definately us a backing board. I have a feeling that
basepaltes might have a tendancy to crack (this could also be a problem with
clipers)
Lester
PS: You not in the SE lower Michigan (Ann Arbor) area are you?
|
|
Message is in Reply To:
 | | Re: Best Way to Cut Baseplates
|
| I like both Lester's idea and yours. Getting cheapo non-Lego bricks is easy in my group and hacking those up sounds more pleasurable than the real stuff. It's been those inside corners that have really been in my head and the drill idea sounds like (...) (25 years ago, 6-Mar-02, to lugnet.general)
|
7 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
