 | | Thoughts on Parts Taxonomy
|
|
Currently, there are three active major part databases out there: Partsref, Peeron Inventories, and the BrickLink Catalog. All have their advantages: Partsref has keywords, cross-referencing to other databases, and usually excellent pictures[1]. (...) (22 years ago, 10-May-02, to lugnet.db.brictionary)
|
| |
| | Re: Going nuts trying to identify a part! (redux)
|
|
(...) BrickLink catalog, added last month by Brett Antaya and spokane1 (Jonathan McKay?). And with luck the inventory of Slave I will be available tomorrow. . . TWS Garrison Remove caps to reply (22 years ago, 6-May-02, to lugnet.db.brictionary)
|
| |
| | Re: Going nuts trying to identify a part! (redux)
|
|
(...) Actually, I don't even recognize the parts. My knowledge of 2001--2002 parts is minimal---I think I have fewer than a dozen open sets from those years. ---...--- TWS Garrison tgarriso@math.purdue.edu (URL) (22 years ago, 6-Apr-02, to lugnet.db.brictionary)
|
| |
| | Re: Going nuts trying to identify a part! (redux)
|
|
(...) You do recognize the part itself, yes? I know the numbers aren't canon yet--but the geometry of the piece (4x4 base to 2x4 top, last brick height toes in at 45-deg, with 2x2 hollow studs and two one- finger click hinge bits) I hope is clear. I (...) (22 years ago, 5-Apr-02, to lugnet.db.brictionary)
|
| |
| | Re: Going nuts trying to identify a part! (redux)
|
|
(...) Nope, sorry, I don't recognize these. Anyone else? ---...--- TWS Garrison tgarriso@math.purdue.edu (URL) (22 years ago, 5-Apr-02, to lugnet.db.brictionary)
|
| |
| | Re: Going nuts trying to identify a part! (redux)
|
|
(...) Thomas--if you've got it in immediate memory, there are two items that've defying my search: The new Jack Stone container (part # stamped on the 4x4x4 container piece is 30639) and the "doors" that connect via a click hinge (numbered 30625). (...) (22 years ago, 5-Apr-02, to lugnet.db.brictionary, lugnet.general)
|
| |
| | Re: Going nuts trying to identify a part!
|
|
(...) Thanks Thomas! LFB (22 years ago, 5-Apr-02, to lugnet.db.brictionary)
|
| |
| | Re: Going nuts trying to identify a part!
|
|
(...) Peeron and at least three sellers on BrickLink call it a Handle 1 x 3 (URL) Garrison (22 years ago, 5-Apr-02, to lugnet.general, lugnet.db.brictionary)
|
| |
| | Re: HELP identify a 2x4 plate, 1/2 thickness (not 1/3)
|
|
(...) Clone? (do they have LEGO(r) on the studs?) Tyco(tm), IIRC, used 1/2 thick plates. But I'm hazy on clones (they're not Lego, after all...) so could be all wet. ++Lar (22 years ago, 24-Feb-02, to lugnet.db.brictionary, lugnet.off-topic.clone-brands)
|
| |
| | Re: HELP identify a 2x4 plate, 1/2 thickness (not 1/3)
|
|
(...) Pedro, good question: No, I was NOT sure they were LEGO, but now that I have checked the studs, they are NOT imprinted with "LEGO", but rather "TYCO" is imprinted on the very center of the plate. Into the trash they go. (Just kidding.) Mystery (...) (22 years ago, 24-Feb-02, to lugnet.db.brictionary)
|
