 | | Hide part in next and subsequent steps...
|
|
Is there a way to hide a part or parts in subsequent steps using mlcad...?.. If there is I am missing it.. Thanks Tom (24 years ago, 26-Sep-00, to lugnet.cad.mlcad)
|
| |
| | Re: Parts selector on the left
|
|
OK! That did it. Thanks. (...) (24 years ago, 25-Sep-00, to lugnet.cad.mlcad)
|
| |
| | Re: Parts selector on the left
|
|
Maybe you changed the viewing angle?! Press right mouse-key in this view, select "View Angle" and in this sub-menu select "3D". Michael Jaco van der Molen <jmolen@globalxs.nl> schrieb in im Newsbeitrag: 39CB64BD.8174FADE@gl...alxs.nl... (...) (24 years ago, 25-Sep-00, to lugnet.cad.mlcad)
|
| |
| | Re: Parts selector on the left
|
|
(...) It's in the Change menu under Settings. Go to the Document tab and set the Default 3D rotation settings to X:23, Y:45, Z:0. This changes the view of the pieces on the left and the camera angle for saving bitmaps of you model. HTH John Gramley (24 years ago, 22-Sep-00, to lugnet.cad.mlcad)
|
| |
| | Parts selector on the left
|
|
Hi all, Why are the parts on the left suddenly shown from top? How do I put the view to 3D again? I cannot seem to find it in the settings. Greetingz... Sjaacko (24 years ago, 22-Sep-00, to lugnet.cad.mlcad)
|
| |
| | Re: "Step" mode for MLCad?
|
|
(...) Thanks a lot, that was exactly the option I was looking for. Regards, Hakan (24 years ago, 21-Sep-00, to lugnet.cad.mlcad)
|
| |
| | Re: "Step" mode for MLCad?
|
|
Hakan, look under "Settings", "Change", the "Rendering" tab, in the Edit-Mode Options box, click "Draw to selected part only". I hope this is what you were looking for. Dennis (...) (24 years ago, 20-Sep-00, to lugnet.cad.mlcad)
|
| |
| | "Step" mode for MLCad?
|
|
Hi, In my previous installation of MLCad, I could step through the parts of a model, and MLCad would only draw the pieces up to the part I stepped to. After a re-install, I can't find an option to enable this behaviour anymore, I always see the (...) (24 years ago, 20-Sep-00, to lugnet.cad.mlcad)
|
| |
| | Re: Pictures of my MLCad MOCs
|
|
(...) I have POV-Ray and L3P but I'm still a bit confused about it. I have used L3P with a bit of success but I couldn't really figure out the coordinate system (I really didn't try that much though) and I'm not real fond of DOS commands. I was (...) (24 years ago, 18-Sep-00, to lugnet.publish, lugnet.town, lugnet.cad.mlcad)
|
| |
| | Re: Pictures of my MLCad MOCs
|
|
Well, why don´t you raytrace the models? Use POV-Ray or try Lightwave for it. For use Lightwave, you need a converter to convert from *.DAT to *.LWO. You can find it at www.joern-thiemann.de/tools; some Demo-Pics too. Greetings... ...Joern Thiemann (...) (24 years ago, 17-Sep-00, to lugnet.publish, lugnet.town, lugnet.cad.mlcad)
|
