|
|
 | | Re: "Step" mode for MLCad?
|
| (...) Thanks a lot, that was exactly the option I was looking for. Regards, Hakan (24 years ago, 21-Sep-00, to lugnet.cad.mlcad)
| | | | | Re: "Step" mode for MLCad?
|
| Hakan, look under "Settings", "Change", the "Rendering" tab, in the Edit-Mode Options box, click "Draw to selected part only". I hope this is what you were looking for. Dennis (...) (24 years ago, 20-Sep-00, to lugnet.cad.mlcad)
| | | | | "Step" mode for MLCad?
|
| Hi, In my previous installation of MLCad, I could step through the parts of a model, and MLCad would only draw the pieces up to the part I stepped to. After a re-install, I can't find an option to enable this behaviour anymore, I always see the (...) (24 years ago, 20-Sep-00, to lugnet.cad.mlcad)
| | | | | Re: Pictures of my MLCad MOCs
|
| (...) I have POV-Ray and L3P but I'm still a bit confused about it. I have used L3P with a bit of success but I couldn't really figure out the coordinate system (I really didn't try that much though) and I'm not real fond of DOS commands. I was (...) (24 years ago, 18-Sep-00, to lugnet.publish, lugnet.town, lugnet.cad.mlcad)
| | | | | Re: Pictures of my MLCad MOCs
|
| Well, why don´t you raytrace the models? Use POV-Ray or try Lightwave for it. For use Lightwave, you need a converter to convert from *.DAT to *.LWO. You can find it at www.joern-thiemann.de/tools; some Demo-Pics too. Greetings... ...Joern Thiemann (...) (24 years ago, 17-Sep-00, to lugnet.publish, lugnet.town, lugnet.cad.mlcad)
| | | | | Pictures of my MLCad MOCs
|
| I have finally posted pictures of my MOCs on my website for all to see. I have posted the DAT files on LUGNET for almost all of them (I haven't posted the house DAT file) so if you want one of them, just do a little searching or e-mail me. I took (...) (24 years ago, 16-Sep-00, to lugnet.publish, lugnet.town, lugnet.cad.mlcad)
| | | | | Re: parts available?
|
| (...) hiya! (...) I'm not sure if you mean you want to create the LEGO sets in MLCAD, or you're using pieces from those sets for your own creations. If it's the former, there's already a version of the 8448 posted to lugnet.cad.dat.models. Steve (24 years ago, 15-Sep-00, to lugnet.cad.mlcad, lugnet.cad, lugnet.cad.dev.org.ldraw)
| | | | | (canceled)
|
| | | | | | Re: Resizing - MLCAD/Ledit
|
| 1) Open your POV-RAY file. 2) Look in the Upper-Left corner/section. 3) It says [160x120, NoAA] or some other resolution. 4) Click on that. 5) Pick the resolution from the drop-down list/menu. Hope this helps. ;-) (...) (24 years ago, 15-Sep-00, to lugnet.cad.mlcad, lugnet.cad, lugnet.cad.ray)
| | | | | Resizing - MLCAD/Ledit
|
| I have just done my first Pov-Ray rendering using LP3. It has turned out nicely except for the fact that it is very small. Can I increase the size of the model in MLCAD/Ledit? Can I increase the size of the model in POV-RAY? Thanks Carl Watson (24 years ago, 15-Sep-00, to lugnet.cad.mlcad, lugnet.cad, lugnet.cad.ray)
|
|
