 | | Re: New part 3648a - 48\1-6edge.dat [DAT]
|
|
0 8-48 Hi-Res Edge 0 Name: 48\1-6edge.dat 0 Author: Lance Hopenwasser <hopenwasser@acm.org> 0 Unofficial Primitive 2 24 1.0000 0.0000 0.0000 0.9914 0.0000 0.1305 2 24 0.9914 0.0000 0.1305 0.9659 0.0000 0.2588 2 24 0.9659 0.0000 0.2588 0.9239 0.0000 (...) (22 years ago, 3-Feb-03, to lugnet.cad.dev, lugnet.cad.dat.parts.primitives)
|
| |
| | Re: New part 3648a - tooth24b.dat [DAT]
|
|
0 Single Tooth (Short) for Technic Gear 24 Tooth 0 Name: tooth24b.dat 0 Author: Lance Hopenwasser <hopenwasser@acm.org> 0 Unofficial Primitive 0 BFC CERTIFY CCW 1 16 0 4.8525 0 1.25 0 0 0 -1 0 0 0 4.75 rect.dat 1 16 1.6875 3.2275 0 0 -1 -.4375 0 0 (...) (22 years ago, 3-Feb-03, to lugnet.cad.dev, lugnet.cad.dat.parts.primitives)
|
| |
| | New part 3648a - Technic Gear 24 Tooth with 3 Axleholes [DAT]
|
|
OK, after much work, refinement, and most especially help from Mark Kennedy, Chris Dee, Steve Bliss, and Orion Pobursky, I have finally finished my first part along with several supporting primitives (thus the cross-post to LCDPP). I would (...) (22 years ago, 3-Feb-03, to lugnet.cad.dev, lugnet.cad.dat.parts.primitives)
|
| |
| | Re: Need for rect primitive with two or one edge?
|
|
Actually, in hindsight, I think maybe it was my brain that was missing. I thought it was missing rect2p.dat, but I just looked at my zip and there is was. It probably wouldn't be a bad idea to run it as a daily job anyway, if it doesn't take too (...) (22 years ago, 3-Feb-03, to lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Re: Making parts 2999 and 2998 work together
|
|
(...) I would move 2999... and do it in this release, partly because it's the sensible and consistent thing to do and partly because it will have less impact if moved now than at any point in future. ++Lar (22 years ago, 3-Feb-03, to lugnet.cad.dev)
|
| |
| | Re: Making parts 2999 and 2998 work together
|
|
(...) I say reposition 2999. I think that the few, if any, models that use this part could be updated with relative ease and the frustration saved by going this route would offset any inconveinence. -Orion (22 years ago, 3-Feb-03, to lugnet.cad.dev)
|
| |
| | Making parts 2999 and 2998 work together
|
|
I posted a 'hold' review on the wheel from the 8080 Super Car (part 2998). You can read it at: (URL). The part file itself is good. Unfortunately, 2998 only fits with part 2999 (see 2999 at (URL). 2999 was released back in 1998. Right now, the two (...) (22 years ago, 2-Feb-03, to lugnet.cad.dev)
|
| |
| | Re: Need for rect primitive with two or one edge?
|
|
(...) What was it missing? We did have a problem running out of disk space recently, that could have caused the trouble. (...) I've rebuilt the zip file. I should probably set that up to run as a daily job. Steve (22 years ago, 1-Feb-03, to lugnet.cad.dat.parts.primitives, lugnet.cad.dev)
|
| |
| | Updated Axle and Connect POV primitives
|
|
I updated the axle and connect primitve POV file. I also added POV code to the axlehole and connect primitves so that L3P add my code automatically. I put these in a zip file that just needs to be put into the /P directory. let me know if these are (...) (22 years ago, 1-Feb-03, to lugnet.cad.ray, lugnet.cad.dev)
|
| |
| | Re: lsynthcp community development project setup on sourceforge
|
|
(...) Don, I look forward to figuring this one out, but since it was not immediately obvious to me how to use it, I put it aside for now. (Just too much crap going on at the moment.) Thanks for bringing it to the Mac. Chris (22 years ago, 1-Feb-03, to lugnet.cad.dev, lugnet.cad.dev.mac)
|
